Search results
Jump to navigation
Jump to search
Page title matches
- The pedal module has two independently working sensors (potentiometer or hall effect) ...electrical connector used. The nominal voltage values are the same for all pedal versions. ...9 KB (1,137 words) - 16:28, 20 December 2024
- ...s Hybrid Control System Reference Manual (RM1075U), Page 05-773</ref>. The pedal should be supplied with a reasonable stable and accurate 5V supply to ensur |+Voltage Output of Throttle Sensors ...1 KB (204 words) - 17:04, 20 December 2024
- Throttle Pedal Variants ...3 KB (340 words) - 17:44, 20 December 2024
- 52 bytes (9 words) - 11:00, 25 March 2025
Page text matches
- The pedal module has two independently working sensors (potentiometer or hall effect) ...electrical connector used. The nominal voltage values are the same for all pedal versions. ...9 KB (1,137 words) - 16:28, 20 December 2024
- ...s Hybrid Control System Reference Manual (RM1075U), Page 05-773</ref>. The pedal should be supplied with a reasonable stable and accurate 5V supply to ensur |+Voltage Output of Throttle Sensors ...1 KB (204 words) - 17:04, 20 December 2024
- ...dard cable throttle pedal, as the gasoline versions were still using cable throttle. ...ce: https://openinverter.org/forum/viewtopic.php?p=73560#p73560</ref>. The pedal should be supplied with a reasonable stable and accurate 5V supply to ensur ...3 KB (477 words) - 16:35, 20 December 2024
- ...not just smooth but becomes sluggish return some previous increments until throttle reaction is acceptable. ...t car on it. You want to hold car in position on slope just using throttle pedal. If there parameters are not good motor will jump or will feel sluggish ...5 KB (900 words) - 23:36, 21 January 2022
- [[File:Honda accelerator pedal sensor 01.jpg|thumb|A better image would be nice, but this is what the sens [[File:Connector pinout.jpg|thumb|Honda accelerator pedal sensor connector pinout<ref>Forum Reference: https://openinverter.org/forum ...3 KB (401 words) - 15:09, 24 March 2026
- === throttle/break pedal wiring: === ==== dual channel throttle: ==== ...8 KB (1,310 words) - 16:54, 17 September 2025
- === throttle pedals === '''[[Honda Accelerator pedal sensor|Honda accelerator pedal position sensor]]''' ...4 KB (432 words) - 07:02, 14 November 2024
- ...rrides the throttle. I.e. if you press both, brake pedal and throttle, the throttle is ignored. ...This output is activated on over current, motor overheat, emergency stop, throttle out of range. ...6 KB (1,045 words) - 15:18, 7 January 2022
- Throttle Pedal Variants ...3 KB (340 words) - 17:44, 20 December 2024
- ...rrides the throttle. I.e. if you press both, brake pedal and throttle, the throttle is ignored. ...This output is activated on over current, motor overheat, emergency stop, throttle out of range. ...7 KB (1,157 words) - 15:18, 7 January 2022
- |Throttle second pot GND |Throttle second pot (signal) ...7 KB (1,242 words) - 08:08, 24 May 2024
- ...rrides the throttle. I.e. if you press both, brake pedal and throttle, the throttle is ignored. ...This output is activated on over current, motor overheat, emergency stop, throttle out of range. ...9 KB (1,408 words) - 19:40, 12 July 2022
- ||5V supply from board for use with throttle pot or hall pedal |Throttle In ...8 KB (1,353 words) - 17:42, 20 December 2024
- ...rrides the throttle. I.e. if you press both, brake pedal and throttle, the throttle is ignored. ...This output is activated on over current, motor overheat, emergency stop, throttle out of range. In SPI mode: SCK ...9 KB (1,487 words) - 13:37, 6 March 2026
- At full throttle an effective voltage of 1700/37813*355=16V is generated. The best way to fi ...pmax''' is the slip frequency at which the motor is run at minimum/maximum throttle. fslipmin is set to the motors optimal slip frequency which can be deduced ...24 KB (3,691 words) - 19:41, 14 March 2026
- * Dual channel throttle pedal (e.g. BMW E36 throttle pedal) #* Throttle pedal to the two inputs ...13 KB (2,111 words) - 15:01, 23 March 2026
- * Throttle mapping === Throttle pedal wiring === ...21 KB (3,199 words) - 13:48, 26 March 2026
- ...led as above - by using digital I/O and directly connecting an accelerator pedal. However, it is also possible to control it directly over CAN: [[CAN commun === Throttle Wiring === ...14 KB (2,416 words) - 23:37, 15 March 2025
- !Note: see this thread regarding throttle pedal safety https://openinverter.org/forum/viewtopic.php?p=75841 this applies to ...5 KB (756 words) - 15:23, 18 April 2026
- ...enclosure which is a nice junction point of various signals like throttle pedal, vacuum sensor and so on. The board handles VW specific CAN messages, Nissa == Throttle Pedal == ...27 KB (4,779 words) - 16:00, 27 November 2024