the settings are read from the eeprom on start up. if the settings show up in the menus they are from the eeprom.
is this issues you are mentioning present on which firmware version? I have as I said never had feedback close to these kinds of issues.
Search found 1341 matches
- Fri May 31, 2024 5:31 pm
- Forum: Battery Managment (BMS)
- Topic: Simp BMS
- Replies: 666
- Views: 293261
- Fri May 31, 2024 2:11 pm
- Forum: Battery Managment (BMS)
- Topic: Mercedes EQS modules with slave BMS boards
- Replies: 9
- Views: 271
Re: Mercedes EQS modules with slave BMS boards
You will need to write custom code to work with the setup you have. The Dilithium bms https://www.thunderstruck-ev.com/mcu.html might work
As their satellite uses the same chip https://www.thunderstruck-ev.com/bms-satellite.html
Best to reach out to Thunderstruck
As their satellite uses the same chip https://www.thunderstruck-ev.com/bms-satellite.html
Best to reach out to Thunderstruck
- Fri May 31, 2024 11:25 am
- Forum: Battery Managment (BMS)
- Topic: Simp BMS
- Replies: 666
- Views: 293261
Re: Simp BMS
That is very unlikely, best to do would be to force a factory reset and then input all your parameters. Most checks are done on which modules have reported themselves, they get "reset" every so often to check that all the values being received are correct and none of them have stopped addi...
- Fri May 31, 2024 11:23 am
- Forum: Battery Managment (BMS)
- Topic: Mercedes EQS modules with slave BMS boards
- Replies: 9
- Views: 271
Re: Mercedes EQS modules with slave BMS boards
Does “Passive cell balancing up to 200 mA (max.) with programmable pulse width modulation” mean it can do some balancing without the master IsoSPI controller? No, passive balancing means it balances by switching resistors across the cells. It is a a dumb front end slave so will report data to the I...
- Thu May 30, 2024 11:39 pm
- Forum: Battery Managment (BMS)
- Topic: Mercedes EQS modules with slave BMS boards
- Replies: 9
- Views: 271
Re: Mercedes EQS modules with slave BMS boards
LTC6813 so its has ISO-SPI
https://www.analog.com/media/en/technic ... 8134fa.pdf
Old chip for something so "new"
https://www.analog.com/media/en/technic ... 8134fa.pdf
Old chip for something so "new"
- Thu May 30, 2024 2:53 pm
- Forum: Battery Managment (BMS)
- Topic: Mercedes EQS modules with slave BMS boards
- Replies: 9
- Views: 271
Re: Mercedes EQS modules with slave BMS boards
Open up the slave module and take detailed pictures of the slave boards.
No point speculating.
No point speculating.
- Mon May 27, 2024 10:22 am
- Forum: Battery Managment (BMS)
- Topic: Simp BMS
- Replies: 666
- Views: 293261
Re: Simp BMS
Please give me the exact firmware number you are using. I have not heard of this issue from anyone else so this sounds quite like a specific problem to you and your setup. You are using the provided .hex to flash the firmware right?
- Sun May 26, 2024 10:28 pm
- Forum: Battery Managment (BMS)
- Topic: Simp BMS
- Replies: 666
- Views: 293261
Re: Simp BMS
Wait you change to which version and the Tesla comms are stable? That is not really logical as the base level software for the comms has not changed since the start.alexbeatle wrote: ↑Sun May 26, 2024 10:21 pm I went back to the firmware revision with which my BMS arrived
- Fri May 24, 2024 9:08 am
- Forum: Battery Managment (BMS)
- Topic: Simp BMS
- Replies: 666
- Views: 293261
Re: Simp BMS
So clearly EMI from the HV. Your wiring twisted as per OEM tesla? are the runs as short as possible? Are the runs not parallel with HV cables/busbars?
- Thu May 23, 2024 10:18 pm
- Forum: Battery Managment (BMS)
- Topic: Simp BMS
- Replies: 666
- Views: 293261
Re: Simp BMS
Impressive, what happens when you power the board via 12V? as your usb might be power limited and you are running 14 modules with not short cable runs.
Also is the code unmodified?
Also is the code unmodified?
- Thu May 23, 2024 5:08 pm
- Forum: Battery Managment (BMS)
- Topic: Simp BMS
- Replies: 666
- Views: 293261
Re: Simp BMS
Yes, that would be the only difference between a not turning and a turning motor. The HV current created EMI.
- Thu May 23, 2024 10:52 am
- Forum: Battery Managment (BMS)
- Topic: Simp BMS
- Replies: 666
- Views: 293261
Re: Simp BMS
Communication crashing due to interference.
- Tue May 21, 2024 9:00 pm
- Forum: Projects
- Topic: [WIP] 1964 Scout LS600H conversion
- Replies: 52
- Views: 18498
Re: [WIP] 1964 Scout LS600H conversion
The slave modules are known for being shitty and prone to issues. Also the celltaps on the modules can get corroded.
- Sat May 18, 2024 2:03 pm
- Forum: General
- Topic: VW GOLF GTE BRAKE SERVO ??
- Replies: 3
- Views: 380
Re: VW GOLF GTE BRAKE SERVO ??
Those are Gen1 Iboosters
- Sat May 18, 2024 11:37 am
- Forum: General
- Topic: VW GOLF GTE BRAKE SERVO ??
- Replies: 3
- Views: 380
Re: VW GOLF GTE BRAKE SERVO ??
It is a gen2 Ibooster, should work just find the right pinout. I have one from a seat same partnumber. I got it working on the bench.
- Wed May 08, 2024 5:59 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombie and GS450H connected but no spin
- Replies: 7
- Views: 246574
- Wed May 08, 2024 5:07 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombie and GS450H connected but no spin
- Replies: 7
- Views: 246574
- Wed May 08, 2024 4:28 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombie and GS450H connected but no spin
- Replies: 7
- Views: 246574
Re: Zombie and GS450H connected but no spin
where is the .JSON with the parameters?
- Wed May 08, 2024 3:47 pm
- Forum: General
- Topic: CAD Models
- Replies: 9
- Views: 1428
Re: CAD Models
https://global.revopoint3d.com/en-uk/pages/portable-3d-scanner-pop3 one of these. Thanks for the heads up! I'll ready my disappointment.... hahahahahaha. Thats an entry level POS. its is priced accordingly 519 gbp you will struggle hard. here is a good review https://www.youtube.com/watch?v=YNpmpQm...
- Wed May 08, 2024 2:01 pm
- Forum: General
- Topic: CAD Models
- Replies: 9
- Views: 1428
Re: CAD Models
Get ready for a really steep learning curve. Which scanner you borrowing?Jacobsmess wrote: ↑Wed May 08, 2024 1:52 pm I'll be borrowing a high quality 3d scanner soon so will scan everything I've got so far.
- Wed May 08, 2024 1:38 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter looses WiFi connection when trying to update
- Replies: 5
- Views: 1007
Re: Zombieverter looses WiFi connection when trying to update
its not swd update... this is covered many times in videos and the forum
You need the other update.
You need the other update.
- Wed May 08, 2024 12:37 pm
- Forum: General
- Topic: CAD Models
- Replies: 9
- Views: 1428
Re: CAD Models
I have now uploaded the GS450h Gearbox and Inverter I scanned
- Wed May 08, 2024 9:53 am
- Forum: Nissan
- Topic: Zombieverter Leaf throttle code
- Replies: 9
- Views: 1748
Re: Zombieverter Leaf throttle code
Im Hoping to get some logs this weekend but in the mean time im going to change 0x1dc as suggested- is it just byte [1] I need to change or [1] & [2]? I cannot quite figure out the cryptic message in the .cpp comments "cryptic" because its just copy paste from a log. image.png Here is...
- Tue May 07, 2024 10:17 pm
- Forum: Charging
- Topic: BMW i3 CCS/charge port controller
- Replies: 1205
- Views: 6588875
Re: BMW i3 CCS/charge port controller
Type 1 LIM does not lock Charge Inlet when AC Charging: -the switch in the charging handle is also the unlock trigger for the catch on the handle. Some EVSEs with tehered type 1s do not have any other way to stop charge. Type 2 LIM locks Charge Inlet when DC Charging: -required by charging standards...
- Tue May 07, 2024 11:59 am
- Forum: Battery Managment (BMS)
- Topic: Engovis EVS-BMS - still available? And any place ship to North America?
- Replies: 9
- Views: 6131
Re: Engovis EVS-BMS - still available? And any place ship to North America?
Vero Electric used to do Simp-BMS distribution in the USA. Since ending the product they have focused on doing their on product.mustardveil wrote: ↑Tue May 07, 2024 1:46 am Hello I am a new member. Is this a reputable place to buy?
Always good experience with Reider (owner of Vero-Electric) and never had bad feedback from customers.