Perfect.... Thanks Greg, Was able to go straight to the Feb 2023 video titled with Blue wifi Module. And Tap into Exactly what I need to help . Many Thanks for the Great Complimation of Damians contributions.. I was struggling to find the right spot..to look. :D it does feel like drinking out of a ...

and this is the state I found that pedal in at the junk yard, nothing but a small scratch on that car, I'm certain it never was raced

the Prius pedal just didn't blow my skirt up, so with more pedals at my disposal I decided to give the 2010 Honda Fit a go

this is the header they go on if you are thinking bare bones build

here is a nice close up from Delphi but they do not mount in this position, what I would call natural horizontal here in the pic, instead they flip on their side and mount vertically, a bit unusual. None of this may make any sense to you until you go to pin one on and then you will have the typical ...

this may help folks find the right pins for the EVBM ZombieVerter VCU if they decide to build their own harness or loose or ruin some in the process, or just need extras, there appear to be two different sizes, and I would recommend the smaller of the two (22-18 AWG) for the synchronous serial wires...

Thanks for helping....have the connections sorted ready for when have a Zombie board prepared. Next to assemble supplied chips, and wifi module. The Damian Maguire video I found has guidance to installing a wifi board , not the Esp one, which could be flipped over and seemingly incorrectly installe...

got her one of these 1400 grid tie inverters for a $100 bucks on eBay, no batteries required

as with any home DIY project a trip to Home Depot is inevitable

for Mother's Day decided to install a little $250 dollar system on her house

used 5 of the 275 watt solar panels I got for $20 bucks each from a friends friend, the deals are out there folks

with a wet spring in the rear view mirror, I decided to take a peak at how my $1,000 DIY solar system is performing

the green means I sold energy back to the utility company that day

I had so much fun making this...

introducing the latest line to our Wood-A-Bility series

sometimes you're allowed to have a little fun

Well nice job with the video... It is all about sensor resolution. 0 to 4095 means your sensor can see in 12bit increments. 12bit is greater parts than 10bit. This means your full sensor resolution is divided into 4095 indivdual parts which are referenced by the chip Aref pin. This pin wil see the ...

Thanks all for your inputs. Had been looking for Prius label, when its presently looked more like Leaf , I Didn't notice the sync serial is universally there.. I guess this is all stated somewhere that I haven't come across... Just wondering best way to guide fumbling folks like myself in the right...

thanks gregski! This feels like something that should be documented in the wiki, but where would a good spot be? update: I added it to the hardware section immediately after the prewired connector w/ leads line item unfortunately formatting is terrible because I don't really know what I'm doing a S...

mane2 wrote: ↑Fri May 10, 2024 4:44 pm How about "Reference Voltage"?

crasbe wrote: ↑Sun May 05, 2024 10:03 pm You know that you can just configure where 100% throttle is, right? So even if your pedal would bottom out at 50% travel, you could configure the ZombieVerter to interpret that as 100%

absolutely

P.S.Mangelsdorf wrote: ↑Fri May 10, 2024 2:38 pm That's how my engineering professors would have described it.

A unitless integer with a range from 0 to whatever.

man just when I thought I knew nothing, you remind me that I know even less !

that looks similar to what's on the Wiki https://openinverter.org/wiki/ZombieVerter_VCU#Installation all you need is the four pairs of wires from the Inverter to the Zombie, there are four sets of three wires shown in the diagram below because the third wire from each wire pair loops back to the inv...

Thanks for info, have been removing some with less sophisticated jewelers screwdriver method. On a related track, pinout for the Zombie board, Mth, Htm, Req, and Clk etc. For use with Prius Nvw30 inverter, Can you point me as where to locate this please.? Thanks. it will be my next video, in the me...

ZombieVerter VCU Throttle Calibration

just came across someone else pointing this out on Instagram

I had a lovely 92 Toyota small pickup like that and luved it