Search found 3295 matches
- Wed Mar 06, 2024 8:17 am
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
After some serious driving with Outlander VCU, for more than 200km stretch... i may share some thought about this VCU. Teensy works really well when it works inside its loop. That means when VCU is activated and car is in FWD or RWD mode drive is very smooth, no jumps or glitches. Torque is somewhat...
- Mon Mar 04, 2024 10:47 am
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
I am back. I made a new wiring for the front elements CAN bus and separated 12V power supply in case that would help with any noise on the line. It didnt! Heater still wouldnt start and i could see speedo jumping at speed. This frustrated me greatly, but l simply turned to sorting some ancillaries s...
- Fri Mar 01, 2024 9:46 pm
- Forum: Projects
- Topic: [WIP] Volvo Vee70 with Outlander Rear Motor
- Replies: 26
- Views: 3562
Re: [WIP] Volvo Vee70 with Outlander Rear Motor
Yes, it's not gonna be a power house but I recon it's going to be fine. You could fit the rear parts of axle of the XC70 to your V70which is driven and fit another outlander motor there. Inverter actually doesnt care where it is located. You could actually connect 2 inverter to a single battery and...
- Fri Mar 01, 2024 8:43 pm
- Forum: Projects
- Topic: [WIP] Volvo Vee70 with Outlander Rear Motor
- Replies: 26
- Views: 3562
Re: [WIP] Volvo Vee70 with Outlander Rear Motor
One is in the oil pan and one is in the engine block itself. The piston of the first cylinder moves freely but the rest of the engine is seized. Hm... i remember a guy who cut down the front part of the Nissan Juke engine and used it to fix the last bearing in place from both sides. In fact he used...
- Fri Mar 01, 2024 2:48 pm
- Forum: Tesla
- Topic: Tesla SDU _> S2000 dash cluster
- Replies: 13
- Views: 1114
Re: Tesla SDU _> S2000 dash cluster
Effectively it's a Arduino Due with two CAN channels. There is also eeprom needed for effective DUE use, wich led me to design my own shield that goes over DUE board and has 2 CAN chips, uln2003 chip for outputs and two small relays for using stronger contactors. Input power is protected by a diode...
- Fri Mar 01, 2024 9:00 am
- Forum: Projects
- Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
- Replies: 166
- Views: 76024
Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
makes sense, i put the inverter back on CAN1, dcdc and shunt on CAN2 and still getting timeout. ill play with the inverter can setting tomorrow ... I have a similar problem with Teensy VCU and my Outlander setup. I use everything from Outlander in Mazda MX-3 car; Inverter, motor, charger and heater...
- Thu Feb 29, 2024 12:49 pm
- Forum: Mitsubishi
- Topic: I just bought a Mitsubishi Outlander charger. - Now What?
- Replies: 30
- Views: 2488
Re: I just bought a Mitsubishi Outlander charger. - Now What?
HAHA! LOL! It is similar here and i am sure Terminator or Predator coming through our house wall would have to spend some days in ER...
- Thu Feb 29, 2024 8:17 am
- Forum: Mitsubishi
- Topic: I just bought a Mitsubishi Outlander charger. - Now What?
- Replies: 30
- Views: 2488
Re: I just bought a Mitsubishi Outlander charger. - Now What?
I see a pattern :o Also ordered same charger from UK ebay seller. This is how mine arrived. Post lady seemed most concerned handing this to me. 20231120_120820.jpg I got two of them from Poland in the same sort of packaging. It seems like this stuff is quite resillient and packaging is there just b...
- Tue Feb 27, 2024 7:23 am
- Forum: Mitsubishi
- Topic: I just bought a Mitsubishi Outlander charger. - Now What?
- Replies: 30
- Views: 2488
Re: I just bought a Mitsubishi Outlander charger. - Now What?
...I must admit I just spent half an hour starring at that thread and spinning my charger around 960° back and forth only to realize you do not show a pic of the "high voltage port gland" for the charger... For ease of use i cut my chargers DC cables and put MC4 connectors on them. This v...
- Sat Feb 24, 2024 1:45 pm
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
I used PWM code for speedo dial and it responded with dial jumping...
Then i put the speedo function after the inverter RPM report function. This is what i get:
Seems like it would want to keep the beat with radio .
Then i put the speedo function after the inverter RPM report function. This is what i get:
Seems like it would want to keep the beat with radio .
- Thu Feb 22, 2024 1:15 pm
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
I need to apply some filtering other than in code really as much of it is of no interest and maintaining 10 msec update on the 285 is a challenge with the dash update True. I am slowly leaning towards using a separate BMS with 2 CAN bus lines. One would drive JK BMS modules at 250kbaud and the othe...
- Thu Feb 22, 2024 7:06 am
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
- Wed Feb 21, 2024 4:08 pm
- Forum: General
- Topic: EV Conversion with Dacia Spring
- Replies: 2
- Views: 928
- Wed Feb 21, 2024 4:07 pm
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
OK now i changed from tone to PWM code and it works...sort of :?. I still get needle to jump by 10km/h. This lets me to belive the problem is not in the code but rather in the CAN bus rutine or chip. It seems like inverter report does not arrive to VCU in time and so speedo is not updated fast enoug...
- Tue Feb 20, 2024 9:33 pm
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
The tone function has another parameter: pulse duration. tone(pin, frequency, duration) And also in your code, line 2026 "tone(OUT9, 3000); " what is it for? You need to enable hardware PWM. The code already contains the library #include "Teensy_PWM.h" frequency = 10000.0f; PWM_...
- Mon Feb 19, 2024 10:49 pm
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
Am I understanding this thread correct you are able to command 280Nm from the stock inverter? I assume that means that you are exceeding the stock 60kw power output? Or is it just hitting 60kw at lower rpm? (I assume current is recorded from the shunt?) Not yet. I reset it back to 230Nm. I managed ...
- Mon Feb 19, 2024 7:35 am
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
You need to check the response message from BMS void canRX_001(const CAN_message_t &msg) { Serial.println(msg.id); Hm... i still have to verify this. In the meantime i noticed my speedo function is misbehaving. The needle is oscillating a lot. I use Tone function for this as it can quickly vary...
- Sun Feb 18, 2024 6:11 pm
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
Are certain BMSs not included in the array, or is data from one BMS partially missing? I have 84S cells as well. But i use 7 BMS modules. Each BMS module is connected to 12S battery module as this was the easiest. When i connect to CAN lines i can see the FF request going out and i see all 7 module...
- Sat Feb 17, 2024 6:22 pm
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
I got it now thanks! Reverse is now good even in uphill. Next i tackled the missing CAN traffic on CAN1 that i setup for JK BMS comms. I found out there was really bad 3V3 connection and i resoldered this link. Now i get good traffic. Because i didnt want to connect BMS requests to shady timers i op...
- Sat Feb 17, 2024 2:16 pm
- Forum: Mitsubishi
- Topic: Rear Drive Unit Continuous Rating?
- Replies: 12
- Views: 3347
Re: Rear Drive Unit Continuous Rating?
My math suggests that 35kw cont, 85kw peak should be sufficient for a 2t vehicle with performance characteristics of a microbus from 1989 - that is, slow, but able to keep going at 100km/h continuously. Well i can say i could get 11s to 100km/h for 1.2T car. I can see max 230A with 320Vdc battery =...
- Sat Feb 17, 2024 2:09 pm
- Forum: Projects
- Topic: [WIP] Volvo Vee70 with Outlander Rear Motor
- Replies: 26
- Views: 3562
Re: [WIP] Volvo Vee70 with Outlander Rear Motor
- I'm not sure if anyone has done that and it's possible that the internal gearing is so high that the car will have trouble accelerating from standstill Well here you can see how i made it... https://openinverter.org/forum/viewtopic.php?p=66698&hilit=mazda#p66698 Also my battle with VCU... htt...
- Fri Feb 16, 2024 4:58 pm
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
Change the -6 for more torque So do i go less than -6? Ok like if the higher number makes more torque? ... Hm... should i increase this condition for throttle position too? if (throttlePosition > 6) { torqueRequest = throttlePosition * 6; // lets make the pedal less responsive *6 inverterFunction =...
- Thu Feb 15, 2024 3:35 pm
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
All three can bus work fine for me. One balancer did not respond well to requests, I replaced it. Tnx i will look into why i cant get any traffic on the lines... On the other hand i see very little torque in reverse. Today i tested this driving in a small hill. It was embarrasing :(. How to up this...
- Wed Feb 14, 2024 6:10 pm
- Forum: Mitsubishi
- Topic: Outlander VCU - Rear inverter, Charger and BMS
- Replies: 405
- Views: 1533048
Re: Outlander VCU - Rear inverter, Charger and BMS
Now finally everything works as it should with VCU. I got good acceleration, good regen response, Nice reverse drive and everything connected to Outlander components is operating aas it should. Acceleration at 13s now. I managed 11s with large torque swings, but it was not comfortable. I setup all a...
- Tue Feb 13, 2024 6:31 pm
- Forum: Mitsubishi
- Topic: Mitsubishi Outlander PHEV heater
- Replies: 145
- Views: 43555
Re: Mitsubishi Outlander PHEV heater
I have very good results using those shady china items for years now... https://www.aliexpress.com/item/1005006244142432.html?spm=a2g0o.productlist.main.15.69fb1413NAkZI7&algo_pvid=ae1846ba-9005-4fac-b52c-1f37876ec270&aem_p4p_detail=202402131030333168637731640080009442613&algo_exp_id=ae1...