Dalas battery emulator doesn't do iso to to query each cell measurement. It does decide some frames it sends out though with normal can [EDIT] Actually, it does look at to a bit of ISOTP can, 0x7BB I think is a response frame ID from the BMS. So I need to do more reading to workout how to expand thi...

Anyone got any info on using ISO TP to request data from a Kangoo BMS, source code would be even better.

Yes for box. Cooling, not sure, probably not, didn't seem to use it in the van

https://openinverter.org/wiki/Renault_Kangoo_36 I've started documenting the pack as I go.

Not checked, but assuming it is 8s modules :D Can't workout how to create a wiki page, so dumping here for now. The pack has 2 low voltage connectors, a black and a grey. [insert mating part numbers] It only has one contactor, rated at 150a and a pre charge relay. No negative contactor. There's a se...

Modules are roughly 14x21x31 cm 16kg each.

My battery pack has arrived. Need to get some can logs and label up the wiring before working out how to cram it all under the bonnet 36kWh 33 usable from a Renault Kangoo

There is no standard list, it's entirely configurable and nothing happens by default (excluding messages for specifically selected hardware/integrations). Someone did start a table trying to standardise OI can messages https://openinverter.org/wiki/CAN_table_CAN_STD One thing though that might be us...

https://openinverter.org/wiki/CAN_communication wiki has information that's also relevant to zombie mapping.

I'm currently stuck in CCS mounting pain too. I've not taken a look at a load of CCS plugs, what sort of clearance is required around the port?
Currently thinking of mounting sideways and wonder if I'll have issues getting the plug in there?

Mine gets pretty toasty. Can logs will help

I'll add a parameter to support both. Ill pm you a bin if you would be ok to test

I get the same can message corruption on my ESP32 based BMS, the messages have CRC though so I can junk rubbish messages but yea, lost confidence in ESP32 for can projects.

Forgot to post past video: https://youtu.be/ycl4T-a7j84?si=s9M0S0GdOrIVSgQI Also just posting my notes here for working out how I'm going to plumb in the AC Using Outlander Compressor the fittings are: #4 15.3mm port to 11.5mm hose I.D. #5 18mm port to 14mm hose I.D. IMG_20240123_133725109.jpg The m...

That part of the harness is simple and easy to make up yourself, the part numbers for the connectors are on the wiki. I had to make mine. I used https://www.ebay.co.uk/itm/204017685320 for the cable. Make sure not to use solid core cable.

That might be of interest, might be massive overkill for the little motor.
viewtopic.php?p=12319&hilit=gasgasless#p12319 what do you think?

Years ago I converted a trials bike, it's somewhere in the projects section, anyway I sold it on as I wasn't using it and the new owner is looking for a motor controller now. Max voltage of 83V and 200a peak, 110a continuous was the claim on the controller. It's a 20s battery. 353110169_108051806624...

Looks the same as the one I've got in the Beetle.

Isn't the transmission oil pump mechanically driven from MG1?

The buck boost absolutely needs to be bypassed, you'll blow stuff up if you don't at higher speeds. Your HV needs connecting directly to the DC bus. If using a replacement logic board, for the gen 3 a dead time is absolutely required also.

The board uses an NCV8401, designed for the job, 12V goes to one side of the contactor coil and the other to the VCU. I see it's written in Arduino framework, I think they restart when serial is connected, but this shouldn't be much of an issue, if the DC bus has been pre-charged and it restarts the...

I'd consider binning off the timer relays, just use the VCU directly to do the pre-charge sequence. Timed pre-charge isn't the best method, if precharge fails, blown resistor for example, then boom, it'll just switch on the main contactor regardless

Your 0x285 message looks funky as too, but it seems to work. Wiki suggests the 3rd byte should be 0xB6 to pull the EVSE into the correct state. Yours is 0xAA. Not sure if this is a full log, but some public EVSEs wont work if you skips state B and jump straight to C. The Pod Points at Tesco for exam...