Hi, I am building a unique project, hoping someone could please help. I am building a STOL drag airplane First type to be electric. I acquired a duel axial motor setup .2 MAGELEC PROPULSION M24P4-D-19 AXIAL FLUX With matching motor controller's, I don't have a compatible vcu. I was hoping someone c...

I just received another heater myself. Its good to have spares. With Outlander parts its simple replacement if something goes wrong.

I used to write Aircraft Maintenance Programs for a living. I will simply add new component page to Mazda manual .

. If it feels like a seesaw over bumps at certain speeds the suspension frequency is off. This is kind of old school for suspension tuining but it works well. Hmmm... could be thats why i feel like suspension vibrates 1/2s after i dove through a pothole. Or is it just old worn 1992 bushings... i wi...

If any of you can recommend some adjustable shocks/springs I would really appreciate it. I used 3cm alu pads with rear shocks as my EV weight distribution changed from 68:32 to 50:50. It caused a weird front axle geometry and funny drive trough turns. When i put the pads at the rear the front actua...

, this is one of the reason I want to try 2" drop spindles on that truck instead of 2" shorter coil springs I am sorry to be late to the party... In the old days (i am not that old) i remember autotuning folks saying how to cheaply lower the car. You wrap the installed spring by moist rag...

Bratitude wrote: ↑Tue Mar 05, 2024 8:59 pm I feel like I’m cheating

I cant see why?

After some serious driving with Outlander VCU, for more than 200km stretch... i may share some thought about this VCU. Teensy works really well when it works inside its loop. That means when VCU is activated and car is in FWD or RWD mode drive is very smooth, no jumps or glitches. Torque is somewhat...

I am back. I made a new wiring for the front elements CAN bus and separated 12V power supply in case that would help with any noise on the line. It didnt! Heater still wouldnt start and i could see speedo jumping at speed. This frustrated me greatly, but l simply turned to sorting some ancillaries s...

Yes, it's not gonna be a power house but I recon it's going to be fine. You could fit the rear parts of axle of the XC70 to your V70which is driven and fit another outlander motor there. Inverter actually doesnt care where it is located. You could actually connect 2 inverter to a single battery and...

One is in the oil pan and one is in the engine block itself. The piston of the first cylinder moves freely but the rest of the engine is seized. Hm... i remember a guy who cut down the front part of the Nissan Juke engine and used it to fix the last bearing in place from both sides. In fact he used...

Effectively it's a Arduino Due with two CAN channels. There is also eeprom needed for effective DUE use, wich led me to design my own shield that goes over DUE board and has 2 CAN chips, uln2003 chip for outputs and two small relays for using stronger contactors. Input power is protected by a diode...

makes sense, i put the inverter back on CAN1, dcdc and shunt on CAN2 and still getting timeout. ill play with the inverter can setting tomorrow ... I have a similar problem with Teensy VCU and my Outlander setup. I use everything from Outlander in Mazda MX-3 car; Inverter, motor, charger and heater...

midway wrote: ↑Thu Feb 29, 2024 12:21 pm Our fences and packaging are made from real wood, and furniture from waste from packaging production
Изображение WhatsApp 2024-02-27 в 22.05.06_199882ef.jpg

HAHA! LOL! It is similar here and i am sure Terminator or Predator coming through our house wall would have to spend some days in ER...

I see a pattern :o Also ordered same charger from UK ebay seller. This is how mine arrived. Post lady seemed most concerned handing this to me. 20231120_120820.jpg I got two of them from Poland in the same sort of packaging. It seems like this stuff is quite resillient and packaging is there just b...

...I must admit I just spent half an hour starring at that thread and spinning my charger around 960° back and forth only to realize you do not show a pic of the "high voltage port gland" for the charger... For ease of use i cut my chargers DC cables and put MC4 connectors on them. This v...

I used PWM code for speedo dial and it responded with dial jumping...
Then i put the speedo function after the inverter RPM report function. This is what i get:
Seems like it would want to keep the beat with radio .

I need to apply some filtering other than in code really as much of it is of no interest and maintaining 10 msec update on the 285 is a challenge with the dash update True. I am slowly leaning towards using a separate BMS with 2 CAN bus lines. One would drive JK BMS modules at 250kbaud and the othe...

midway wrote: ↑Thu Feb 22, 2024 6:57 am Call the speedo() function after receiving a response from the inverter.

Ah!!! Nice idea. Will test this today thanks.

RoLee wrote: ↑Fri Aug 25, 2023 3:26 pm What about Dacia Spring Electric as a Source for all neccesary components for EV Conversion?
Any opinions or knowledge?

Motor is rather small, maybe 28kW?

OK now i changed from tone to PWM code and it works...sort of :?. I still get needle to jump by 10km/h. This lets me to belive the problem is not in the code but rather in the CAN bus rutine or chip. It seems like inverter report does not arrive to VCU in time and so speedo is not updated fast enoug...

The tone function has another parameter: pulse duration. tone(pin, frequency, duration) And also in your code, line 2026 "tone(OUT9, 3000); " what is it for? You need to enable hardware PWM. The code already contains the library #include "Teensy_PWM.h" frequency = 10000.0f; PWM_...

Am I understanding this thread correct you are able to command 280Nm from the stock inverter? I assume that means that you are exceeding the stock 60kw power output? Or is it just hitting 60kw at lower rpm? (I assume current is recorded from the shunt?) Not yet. I reset it back to 230Nm. I managed ...

You need to check the response message from BMS void canRX_001(const CAN_message_t &msg) { Serial.println(msg.id); Hm... i still have to verify this. In the meantime i noticed my speedo function is misbehaving. The needle is oscillating a lot. I use Tone function for this as it can quickly vary...

Are certain BMSs not included in the array, or is data from one BMS partially missing? I have 84S cells as well. But i use 7 BMS modules. Each BMS module is connected to 12S battery module as this was the easiest. When i connect to CAN lines i can see the FF request going out and i see all 7 module...

I got it now thanks! Reverse is now good even in uphill. Next i tackled the missing CAN traffic on CAN1 that i setup for JK BMS comms. I found out there was really bad 3V3 connection and i resoldered this link. Now i get good traffic. Because i didnt want to connect BMS requests to shady timers i op...