Search found 787 matches
- Sun Oct 08, 2023 2:56 am
- Forum: Open Tasks
- Topic: Make Nissan Leaf Gen3 adapter board
- Replies: 62
- Views: 22266
Re: Make Nissan Leaf Gen3 adapter board
I’ll make some calls, I know some one with a gen 3
- Sat Oct 07, 2023 1:12 am
- Forum: Projects
- Topic: (driving) Leaf swapped vw golf cabriolet
- Replies: 31
- Views: 9292
Re: (WIP)Leaf swapped vw golf cabriolet
Smart two four battery mounted. Pretty simple frame!
Just some angle iron and a few tabs.
leaf 12v line/fuse terminal fits perfectly to the stock 12v battery location as well- Fri Oct 06, 2023 3:01 pm
- Forum: Projects
- Topic: (driving) Leaf swapped vw golf cabriolet
- Replies: 31
- Views: 9292
Re: (Wip)Leaf swapped vw golf cabriolet
Got the 2 side motor mounts mocked up! The leafs torsional mount is on the back of the gearbox, so I’m going to make a cradle that wraps underneath the gearbox. the cradle will mount to the front beam in the engine bay and the engine mount just below the firewall. the leaf mount will then float on t...
- Thu Oct 05, 2023 12:41 am
- Forum: Projects
- Topic: (driving) Leaf swapped vw golf cabriolet
- Replies: 31
- Views: 9292
Re: Leaf swapped vw golf cabriolet
Becareful you might might end up finding that the Smart packs tend to go into "scrap yard mode" and destory the cells intentionally. Check you do not have a pack that is capable of doing this, or worse has done this. iv heard of this, bms is currently disconnected. but haven't probed them...
- Tue Oct 03, 2023 7:25 pm
- Forum: Projects
- Topic: (driving) Leaf swapped vw golf cabriolet
- Replies: 31
- Views: 9292
Re: Leaf swapped vw golf cabriolet
smart four2 battery uses a ODU 2 pole HV connector, wrecker wants 300$ for the battery cable so thats a no go. https://d1v1e13ebw3o15.cloudfront.net/data/12033/pool_and_spa_master/1335230946_baukasten.jpg the connectors seem to be unattainable, but the matting pins seem to be available https://odu-a...
- Tue Oct 03, 2023 6:50 pm
- Forum: Projects
- Topic: (driving) Leaf swapped vw golf cabriolet
- Replies: 31
- Views: 9292
(driving) Leaf swapped vw golf cabriolet
Might as well start a thread on another car I’m working on: Mk1 VW cabriolet 13A1849C-9199-473C-83C6-154000EFC249.jpeg here's the recipe: Zombieverter VCU Full gen2 nissan leaf stack(including leaf gearbox) smart four2 17kwh battery pack my leaf-to-vw drive shaft adapters with a type 2 axle flange. ...
- Thu Sep 28, 2023 8:31 pm
- Forum: Nissan
- Topic: Leaf Gen 1 Inverter Board
- Replies: 319
- Views: 179387
Re: Leaf Gen 1 Inverter Board
heres an stl of the box
- Thu Sep 28, 2023 1:49 pm
- Forum: Nissan
- Topic: Leaf Gen 1 Inverter Board
- Replies: 319
- Views: 179387
- Thu Sep 28, 2023 3:51 am
- Forum: Nissan
- Topic: Leaf Gen 1 Inverter Board
- Replies: 319
- Views: 179387
Re: Leaf Gen 1 Inverter Board
I’ll post them as a stl that’ll be much easier for everyone
- Wed Sep 27, 2023 12:40 pm
- Forum: Nissan
- Topic: Leaf Gen 1 Inverter Board
- Replies: 319
- Views: 179387
Re: Leaf Gen 1 Inverter Board
If not did anyone ever design an enclosure that can be 3D Printed for it? I can easily bodge something together but it would be nice to have something properly designed for the job. Thanks I found the oem cad files, cleaned them up and posted them here : https://github.com/bratindustries/molex-head...
- Sun Sep 24, 2023 10:40 pm
- Forum: Tesla
- Topic: Base vs. Performance model
- Replies: 1
- Views: 774
Re: Base vs. Performance model
The only difference is the IGBTs. They are just rated for more in the performance units. Regarding the oi board, the power you make will be based off of the parameters you setup. batteries play a huge factor in this as well as how much voltage sagg they exhibit under heavy loads. John volk got some ...
- Sun Sep 24, 2023 3:52 pm
- Forum: General
- Topic: Throttle Cable Adapter Best Practices?
- Replies: 14
- Views: 4904
Re: Throttle Cable Adapter Best Practices?
https://www.evwest.com/catalog/product_ ... cts_id=418
or a throttle body sensors off a intake manifold.
A drive by wire pedal is better because there is less moving parts—less chance of failure, and less mechanical play
or a throttle body sensors off a intake manifold.
A drive by wire pedal is better because there is less moving parts—less chance of failure, and less mechanical play
- Mon Sep 11, 2023 2:43 am
- Forum: Mitsubishi
- Topic: Mitsubishi Outlander rear axle
- Replies: 138
- Views: 46626
Re: Mitsubishi Outlander rear axle
Really interested in the answer to this. Just starting to plan my VW T2 conversion and will be either using an Outlander motor with your shaft adapters , or an imiev one if it does turn out they fit. Comparing driveshaft photos on ebay, the outlander and imieve certainly *look* very similar at moto...
- Fri Sep 01, 2023 1:35 am
- Forum: Mitsubishi
- Topic: Mitsubishi Outlander rear axle
- Replies: 138
- Views: 46626
Re: Mitsubishi Outlander rear axle
any one have a imiev rear drive unit? from some info gathered, it looks like the axles..maybe the entire unit is the same?
- Mon Aug 28, 2023 7:44 pm
- Forum: Mitsubishi
- Topic: Mitsubishi Outlander rear axle
- Replies: 138
- Views: 46626
Re: Mitsubishi Outlander rear axle
Just wondering is there some standard for distance between flanges/stubs? If replacing VW transmission model XYZ with mitsubishi rear diff with these stubs, will original drive shafts fit lengthwise? Most diffs are pretty similar in spacing, from the last measurements I took, was about the same spa...
- Mon Aug 28, 2023 7:39 pm
- Forum: Classifieds
- Topic: Nissan Leaf Gen2 openinverter board fully assembled
- Replies: 8
- Views: 3669
Re: Nissan Leaf Gen2 openinverter board fully assembled
Great. Sounds promising. Quick question: Can this board cover VCU duties for the build (as well as inverter control) or would i need an external VCU product (ex resolve or zombieverter)to cover the basic imputs/outputs to control the car? I am doing gen 2 leaf (PM 56 motor/inverter/pdm) conversion ...
- Sat Aug 26, 2023 7:03 pm
- Forum: Projects
- Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
- Replies: 166
- Views: 63352
Re: [DRIVING] 1983 Subaru BRAT
little bit of maintenance; took my pack apart and wired all 3 m3 modules in parallel and let them sit for a few hours. 2 packs were 90v and one was 86, so now pack to pack they are balanced. * note with anyone looking todo the same: be warry, i did this when the packs where at a low state of charge,...
- Sat Aug 26, 2023 6:52 pm
- Forum: General
- Topic: Parameter database doesn't browse well
- Replies: 9
- Views: 5022
Re: Parameter database doesn't browse well
upload button is gone
i think it would be great if some of the prams where updated, i wanted to push my leaf prams,
maybe johu you can push yours up? the gt86 ones are a bit dated
i think it would be great if some of the prams where updated, i wanted to push my leaf prams,
maybe johu you can push yours up? the gt86 ones are a bit dated
- Sat Aug 26, 2023 6:48 pm
- Forum: Projects
- Topic: Wind turbine with Tesla Drive unit
- Replies: 8
- Views: 947
Re: Wind turbine with Tesla Drive unit
tesla unit is pretty over kill and kind of cumbersome. but for a large scale turbine it could be made to work. not to mention the motors are very intergraded with the gearboxes. so mechanically theres a challenge there smaller units like the Hyundai HSG would make a excellent wind turbine generator....
- Sat Aug 26, 2023 1:31 am
- Forum: Projects
- Topic: 1967 “voltswagon” split window bus
- Replies: 7
- Views: 1382
Re: 1967 “voltswagon” split window bus
rotated the full stack 90 degrees. mount design is drilling down to something quite simple and elegant. will most likely cast the main parts out of aluminum, and use swaged tube and rod ends. full bolt on kit. bottom mount on the engine horns, and 2 side mounts triangulating to the torsion tube. dif...
- Sat Aug 26, 2023 1:19 am
- Forum: Inverters / Motor Controllers
- Topic: Inverter Firmware 5.27.R
- Replies: 18
- Views: 7312
Re: Inverter Firmware 5.27.R
Some code says more than 1000 words: if (!(Param::GetBool(Param::din_forward) ^ Param::GetBool(Param::din_reverse))) selectedDir = 0; if ((int)Encoder::GetSpeed() < Param::GetInt(Param::dirchrpm) && !potPressed) selectedDir = userDirSelection; Neutral selection is immediately applied while ...
- Fri Aug 25, 2023 11:37 pm
- Forum: Mitsubishi
- Topic: Mitsubishi Outlander rear axle
- Replies: 138
- Views: 46626
Re: Mitsubishi Outlander rear axle
0D974043-12FD-40A9-BE24-EE31EE79AD30.jpeg 9138D687-4325-42F0-8DF1-B7356301457C.jpeg Stub shafts are done. with some minor shaving of the plugged coolant port on the motor, type 2 (100mm) cv flanges fit nicely Type 1 (90mm) (vw beetle) fit great as-is. 108mm or 930 flanges should fit, but with a lot...
- Fri Aug 25, 2023 2:11 pm
- Forum: Projects
- Topic: 1967 “voltswagon” split window bus
- Replies: 7
- Views: 1382
Re: 1967 “voltswagon” split window bus
How will the driveline look? I've seen one other bus with a Leaf stack, and one of the drive shafts had to be really short with a pretty extreme offset from diff to hub. with my drive shaft adapters we ditch the jackshaft/ support bearing. we are centering the diff in the frame horns, so equal axle...
- Fri Aug 25, 2023 2:06 pm
- Forum: General
- Topic: Altering regen on the fly
- Replies: 5
- Views: 934
Re: Altering regen on the fly
you can alter regen on the fly with a pot directly. can is not your only option.
parameter: brknompedal / brakeregen
if your wanting to have the Arduino control regen can is the safest
parameter: brknompedal / brakeregen
if your wanting to have the Arduino control regen can is the safest
- Thu Aug 24, 2023 9:36 pm
- Forum: Classifieds
- Topic: outlander rear motor drive shaft adapters
- Replies: 0
- Views: 1196
outlander rear motor drive shaft adapters
after another long wait, the outlander rear motor drive shaft adapters are done! the outer end is a vw beetle (33spline) stub, so stock beetle (90mm) flanges or the 100mm/108mm EMPI conversion flanges work with it (with some minor shaving of the motor case) cold rolled out of 4140 chromoly steel, so...