Just to be sure: Control is the inverter PWM pin(s) and Load is the Teensy PWM signal?
Using the 10k resister to lower the voltage. When I get an n channel mosfet, would 12v be ok?
Thanks again. Got 2 more Teensy 3.2 coming. I socket mounted the Teensy just for this reason.
Thank you.

From your pictures I can’t see any of the current sensors connected? If you leave them disconnected and the pins are floating without turning them off in code there’s and chance the the code will see a current higher than the current limit and not increase pwm, I also can’t see anything there for d...

What does your “throttle PWR actual” read when you press the throttle if this changes from 0 then you are making pwm, does your teensy pwm 4 trigger a logic level fet that drives all of the inverter pwm pins low? Also why remove the inverter temperature part of the code? This gives you on chip moni...

Hard to see from your pictures exactly how your hv inverter wiring is done, you should have battery positive and negative present at the inverter brick inputs, battery neg also connects to motor neg, and motor pos connects to phase outputs, Maybe post a copy of your modified code? And maybe a scree...

I put together a Teensy based Prius Gen 2 Inverter control box based on your box design. I modified my inverter by removing the booster bits and tied the two output buses together. I modified the Teensy code a bit. Changed low battery value, commented out BMS stuff (I don't have one). Also took out ...

will need to double check but from memory: all digital inputs are no inverted opto isolated using pc817 with 1k on the input 10k pulldown on the output, voltage dividers for GIVA, GIWA, MIVA, MIWA current sensors have a diode inline on the input so we only see + voltage and with 20k inline and 10k ...

carsondarling wrote: ↑Fri Jul 23, 2021 7:34 pm

• Remove boost controller
• Remove boost reactor

I don't know what these two parts are or look like.

Are they bolted in and can be unbolted and removed?

Can they be seen in your picture of the prius controller?

Thanks

Eric

Thank you for the hardware info. I'm a software guy so it will take me a while to understand what you posted. Will dig in and see how far I can get. Much appreciate you posting this info. Do you have any pictures of your board?
Eric

Looking for schematics of your dc controller board so I can build my own. Got the code, looks good. Just need to build a board to control the Prius Gen 2 inverter. Schematic and BOM needed.
Thanks for your help.
Eric

I have run out of options and time.
Monetary incentive is on the table.
Email me at esoneson@protonmail.com to discuss.
Thank you all for your patience and help.
Eric Soneson

I ordered some more parts frim digikey to build another damien-dc-motor-controller. When I first started to build my own card I had ordered 3 boards. So I decided to start again fresh. I added each part, checking to make sure there were no shorts on each contact for each component. And checked volta...

I just got a single channel hand held scope. I'll see what I can find on the output of the DC controller (pwm generator).

Eric

On this subject I have redesigned this board to utilise JLCPCB parts and have a bunch of ten on the way fully populated bar the screw connector. Once received I will do a video showing how it all wires up. I would like to have one of these boards. I don't see them on your web page. If you don't hav...

Progress.....not with this yet. But to avert frustration I installed my J1172 receptacle in the gas filler. Added necessary 50 amp fuse and relay for my cabin heater, relays for my cooling fan and circulation pump for inverter and charger. Tested charger controller can communications. Installed heat...

I asked around on other ev forums if anyone has accomplished the prius-gen2-dcmotor-controller-dcmotor-combination. Got no positive response.
Eric & White Arrow

GENERAL QUESTION

Is there anyone out there who has successfully controlled a DC motor with a Prius Gen 2 inverter using Damien's DC Motor Controller?

Anyone? Anyone?

Post here or message me.

Jack, I now have two 12volt sources for this experiment. 1 12 volt battery connected to the HV input to the inverter (negative on top port, positive on bottom port). 1 12 volt battery that connects to the two pin connector (+ on top and - on bottom). This 12 volt source is used to connect to the Pin...

Well, lets take the controller out of the picture and test just the inverter. Unhook the motor and all the HV battery lines from the inverter and hook up a 12v power source to the inverter rails, with 12v to pin 25 (MG2 shutdown), ground one of the pwm signal lines and then you should have positive...

JackTerminus, In that same video you posted Damien mentions that the pwm signal he is generating gets boosted to 12 volts before being fed to the Gen 2 PWM pin. I had seen the same voltage earlier and was confused.....but this is expected. As soon as I can (cold weather prevails) I will monitor PIN2...

Hey Eric, sounds like you have everything wired up right, is your inverter casing grounded to chassis? you could check the voltage on pin 27 and 22 (MG2 Inverter Fail & MG1 Inverter Fail) IIRC they are around 2.5v when all is well and jump up closer to 12v when the inverter is in fault. [Pin 27...

One Prius Gen2 Inverter + one Prius Gen2 DC Motor Controller + instructions = Control of Current to DC Motor correct:) I have my Prius Gen 2 inverter installed. My 167 volt pack connects to the inverter. Batt Pos to Inverter Pos, Batt Neg to Inverter Neg with working pre-charge delay. Pack voltage+...

Thank you SceroccoEV for your sugestion for my White arrow with 9 inch dc motor and Prius gen 2 inverter. I pulled Pin 14 GSDN and Pin 25 high with 12 volts. I then tested the inverter again. Now I have the output to the 12 volt battery working with 14.5 volts charging the car battery. But I get no ...

I need a little help getting my Prius Gen 2 inverter to come alive. Here is what I have: 167 volt lithium pack HV control: 2 contactors for bat neg and 2 contactors for bat positive Bleeder resistor connected between bat neg and controller neg All three Prius inverter MG1 and MG2 output phases conne...

If I am not mistaken, Damien's tests for MG1 and MG2 were conducted using only one phase for each test before the Prius shut down. So 250 and 360 amps represents 1/3 of the potential total amps possible for each motor.

Thank your SciroccoEV!!
That info is perfect and complete. Much appreciated. Now back to my BMW 318i 'White Arrow" wiring tasks.
Eric