A Prius inverter and STM32 control board should be able to perform zero export control with wired sensors.
An off the shelf PV inverter that doesn't support zero export probably won't work too well for zero export, zero export needs fast response on the order of milliseconds or less.
Search found 64 matches
- Sat May 20, 2023 3:06 am
- Forum: V2x
- Topic: Using a DC-DC to simulate a solar cell for MPP tracking
- Replies: 4
- Views: 3627
- Sun Sep 04, 2022 4:32 am
- Forum: Toyota/Lexus
- Topic: Prius Gen2 A/C compressor inverter
- Replies: 22
- Views: 6737
Re: Prius Gen2 A/C compressor inverter
What chip is providing the PWM signals? Could it be reprogrammed or replaced with a generic digital power microcontroller on an adapter board?
- Sat Jul 09, 2022 3:24 am
- Forum: Toyota/Lexus
- Topic: Prius C Inverter
- Replies: 2
- Views: 595
Re: Prius C Inverter
Prius C and Yaris inverters have different part numbers but appear virtually identical inside, I'm pretty sure the only difference is some minor firmware differences.
- Sun Feb 13, 2022 12:02 am
- Forum: Toyota/Lexus
- Topic: Prius Gen 3 Mains 3 Phase Inverter Logic Board
- Replies: 20
- Views: 11256
Re: Prius Gen 3 Mains 3 Phase Inverter Logic Board
I'm in the US and have a small mill with a 3 phase motor which will be the first thing we try to use this for. The data plate says 230/460V--Damien's posts above say 400V. The motor definitely will be loaded, so I wouldn't expect 400V to work. The motor specifying two voltages means it likely can b...
- Fri Jan 07, 2022 3:00 am
- Forum: Toyota/Lexus
- Topic: Gen 3 inverter converter control software
- Replies: 275
- Views: 68824
Re: Gen 3 inverter converter control software
I've used an outlander charger due to my battery voltage and only having access to single phase. My full voltage is higher than rectified single phase so cannot use bucking. You can connect a bridge rectifier to the low voltage side of the boost converter and then use the boost converter to step it...
- Mon Dec 27, 2021 4:16 am
- Forum: Toyota/Lexus
- Topic: Gen 3 inverter converter control software
- Replies: 275
- Views: 68824
Re: Gen 3 inverter converter control software
I reverse engineered the power board a little more and found that pin 30 is high rail OVP and pin 26 is low rail OVP. For my Prius C inverter, the trip points are 700V and 275V. (Could not determine exactly since I was using a CCFL inverter on a bench supply plus some rectifiers to supply the test v...
- Wed Dec 15, 2021 3:44 am
- Forum: Toyota/Lexus
- Topic: Toyota Auris and Yaris Inverter Logic board
- Replies: 140
- Views: 41587
Re: Toyota Auris and Yaris Inverter Logic board
I am interested in the operation of the inverter at voltages up to 390V, is it possible If you apply that to the high side, it will work. If you want to boost it a little (up to 520V, the rated high side voltage), connect your source between low side and high side, but then the current will be limi...
- Mon Dec 13, 2021 12:20 am
- Forum: Toyota/Lexus
- Topic: Prius Gen3 Inverter Hacking
- Replies: 323
- Views: 68214
Re: Prius Gen3 Inverter Hacking
What's the mapping of the power board temperature signal voltages to temperature?
- Sun Dec 05, 2021 2:48 am
- Forum: Toyota/Lexus
- Topic: Yaris Inverters?
- Replies: 45
- Views: 11227
Re: Yaris Inverters?
Quick update, I decided to measure the DCR of the boost inductor and it's 16.5 milliohms. Combined with the inductance reading of 235uH, that means to do DCR based current sensing, a 100k resistor and 150n capacitor should work. (Not tested yet.) I'm now getting the impression that the ASIC on the o...
- Thu Nov 11, 2021 2:25 am
- Forum: Toyota/Lexus
- Topic: Prius Gen2 Adapter Board for CHARGING
- Replies: 242
- Views: 37728
Re: Prius Gen2 Adapter Board for CHARGING
Just had another idea these days: If we want to do low power BOOST charging we should be able to use the auxiliary A/C compressor inverter to rectify 1-phase AC for us :) It feeds into the low voltage side of the buck/boost converter, so with the batteries connected to the DC bus on the high voltag...
- Wed Oct 20, 2021 12:07 am
- Forum: Toyota/Lexus
- Topic: GS450H Discussion
- Replies: 377
- Views: 78910
Re: GS450H Discussion
Might it be possible to use a fuel pump as the electric oil pump?
- Mon Oct 18, 2021 4:49 am
- Forum: Toyota/Lexus
- Topic: GS450H Discussion
- Replies: 377
- Views: 78910
Re: GS450H Discussion
It looks like if the ring gears are welded in place, MG1 would have a direct coupling to the wheels allowing MG1 to provide reverse.
- Fri Oct 08, 2021 3:38 am
- Forum: Toyota/Lexus
- Topic: Prius water pump wiring diagram
- Replies: 14
- Views: 4727
Re: Prius water pump wiring diagram
From what I could find there are two part numbers for this pump, G9040-48020 which is replaced by G9040-47090 so my hope is that the later will be more reliable. Time will tell... Here's a teardown of the old, unreliable one: http://techno-fandom.org/~hobbit/cars/ipump/ Might it be possible to use ...
- Tue Aug 31, 2021 1:08 pm
- Forum: Toyota/Lexus
- Topic: Prius Gen2 Adapter Board for CHARGING
- Replies: 242
- Views: 37728
Re: Prius Gen2 Adapter Board for CHARGING
Might be interesting to explore the idea of using MG1 as an inductor for charging, just like the Renault Zoe. Easy way is to add a bridge rectifier with the output connected between phase B (since phases A and C have current sensors) and HV ground.
- Sun Aug 01, 2021 1:35 am
- Forum: Toyota/Lexus
- Topic: Tapping in to Prius HV battery
- Replies: 2
- Views: 878
- Fri Jul 02, 2021 3:29 am
- Forum: Toyota/Lexus
- Topic: Lexus GS450H VCU Support Thread
- Replies: 775
- Views: 567572
Re: Lexus GS450H VCU Support Thread
Earlier tested supplying inverter from 24V batteries, but 30A fuse blows if added throttle "bit too much" still could not get motors to spin. Now tried 60V power supply and motor will not spin using even lets say 5-6A current or even some more. Input current is proportional to throttle va...
- Fri Apr 09, 2021 1:34 am
- Forum: Toyota/Lexus
- Topic: 450h Spinning! Whats Next?
- Replies: 8
- Views: 2330
Re: 450h Spinning! Whats Next?
Any recommendations on where I could get a pre charge resistor? ZeroEV looks pretty good for a 100W resistor. Water heater element, cheap and commonly available. Or if you have a high voltage cabin heater, you can have it double as the precharge resistor and the precharge relay will double as the h...
- Sun Feb 21, 2021 3:19 am
- Forum: Toyota/Lexus
- Topic: Gen2 vs Gen3
- Replies: 8
- Views: 2195
Re: Gen2 vs Gen3
Gen3 supports "tristating" where you switch between high on and off or low on and off with the diodes conducting as needed during the "off" time, that's not necessary for motor control but for other purposes like building a grid tied inverter, it can make a big difference.
- Tue Feb 16, 2021 10:56 pm
- Forum: Toyota/Lexus
- Topic: Gen 3 inverter converter control software
- Replies: 275
- Views: 68824
Re: Gen 3 inverter converter control software
You could use a SCR to phase angle cut the AC voltage as needed, then bypass with a contactor to eliminate the losses. Main downside is slower charging at lower pack voltage due to lower power factor.
- Tue Feb 09, 2021 3:06 am
- Forum: Toyota/Lexus
- Topic: GS450H Discussion
- Replies: 377
- Views: 78910
Re: GS450H Discussion
That's quite right Tony, stator winding DC resistance and you're absolutely right to remove cables so that the readings you took would be accurate if you had used a milli-ohm meter. Stator winding resistance is measured in milli-ohms so your meter is not designed for that purpose. I realise I'm ask...
- Tue Feb 09, 2021 2:53 am
- Forum: Toyota/Lexus
- Topic: Gen 3 inverter converter control software
- Replies: 275
- Views: 68824
Re: Gen 3 inverter converter control software
The problem is the voltage range.... 2.7vx96=259 actually 3v is a better as fully discharged is 288v fully charged is 400v AC mains 230v plus 10 minus 6 therefore 216 to 253 rectified 304 to 357. If you are doing some power factor boosting.... It's what happens when your peak voltage is less than y...
- Mon Nov 23, 2020 2:02 am
- Forum: Toyota/Lexus
- Topic: Prius Gen2 Adapter Board for CHARGING
- Replies: 242
- Views: 37728
Re: Prius Gen2 Adapter Board for CHARGING
I'm working on a FPGA based controller to run a Prius inverter for zero export inverter operation, but I'm using a Gen3 which allows independent control of the high and low sides so that a high impedance state is possible. Then by alternating H/Z or L/Z, it is possible to source to the positive part...
- Thu Oct 22, 2020 2:40 am
- Forum: Toyota/Lexus
- Topic: 'Home battery' sanity check?
- Replies: 8
- Views: 1750
Re: 'Home battery' sanity check?
It'd be a shame to lose the backup, and I'm not worried about rules and regs particularly. Let's keep it hypothetical :-) True, inductors will have to be manufactured as well. They'll be fairly large! In my design, I'm using the third phase as a dedicated UPS output. That allows for a zero switchov...
- Tue Oct 20, 2020 1:22 pm
- Forum: Toyota/Lexus
- Topic: 'Home battery' sanity check?
- Replies: 8
- Views: 1750
Re: 'Home battery' sanity check?
If you don't need whole house backup, it's far less invasive to make it a zero export inverter. That is, it connects to the breaker panel via a dedicated circuit and sensors are used to limit the current it sources so that it does not export to the grid. In doing so, it can simply plug into that ded...
- Wed Oct 14, 2020 1:28 am
- Forum: Toyota/Lexus
- Topic: Toyota Auris and Yaris Inverter Logic board
- Replies: 140
- Views: 41587
Re: Toyota Auris and Yaris Inverter Logic board
When paralleling transistors, it's often a good idea to have resistors to ensure current sharing. Run two sets of wires about the same length for the MG1 and MG2 outputs, but MG2 should use wire with about twice the copper cross section as MG1 since MG2 is rated for more current.