HI there, up to now everything is spot on, is there anyone know about a clutch in rear diff of peugeot 508 hybrid, i need PWM controller for magnetic clutch of the peugeot 508 rear axle, can some one help me with parameters?
thank you

Lovely, now the motor spining very well, just stuck on 2500 RPM and continue to 4000-4500 RPM, set “lqminusld=1.1“ but will make a final settings when the axel is on a car loaded, is there any other parameter need to be configure before go up the axle on a car?

{ "iqkp": 32, "idkp": 32, "curki": 20000, "vlimflt": 10, "vlimmargin": 2500, "fwcurmax": -100, "syncofs": 63030, "lqminusld": 0, "fluxlinkage": 90, "syncadv": 10, "polepairs": 6, "respo...

I don’t need the 12000RPM, only need 4000rmp so need to set “fmax=400”, “throtcur=4” “potmin=1000” now when the release the throttle the motor stop immediately, when press sharply the motor start to “jump”

what need to do next?

Correct! Thank you, change the value to 400Hz on “fmax”, hit 4000-4500 rpm, but when release the throttle continue to spin with high rpm, aslo in a middle rmp stuck.#bosch SMG 180/120

Replace the throttle pedal with new one but is some, when press just hit 2200-2300 rmp but not smooth rotation, when change the “throtcur=3-4 or 5” the motor just stuck and not rottate.

Hi, with “sincofs=63030” the motor spin very quiter, i like it!! With right direction,manualiq=35A-40A the motor spin with ~3200RPM, 196v X 16(volt/rpm) = ~3200RPM max for this voltage, so with 35-40A run on max rpm but when is with full throttle press only 2000RPM, What i need to calibrate now to u...

With the new i don't have runaway, when release the trottle the motor stop spining in both side, is that mean the “syncofs=63030” is the correct one, also the rotate dir. on my wheels now is correct, Is it ok to use the motor with this “syncofs”

This morning i do “syncofs=30250+32768=~63030” the motor spin in both side with +-3A, in both side ~2000 rpm, may be the new “syncofs=63030” is the correct one.

Ok friends may be now is OK, Test many “syncofs” but finally found may be the correct one. “syncofs=30250” on manualid=10,20,50,100 even 120A does not spin the motor, just a bit vibration, than manualid=0.1 with manualiq= -3 and 3 the motor spin smooth in both side with a bit different RPM, -3A= ~36...

WE DO IT!! change the “respolepairs=6” and “pinswap=7” the motor spin very well.(will upload a video in youtube) First test: Voltage 131v The motor go to ~1600rmp with il1 and il2 to ~80A 131v X 80A = 10 kw ~13hp Second test: Votage 198v The motor go to ~2200 rmp with il1 and il2 to ~24A 198v X 24A ...

I found the information about “polepairs=6” for this kind of motor in other forum Bosch SMG180/120 PMS Motor has: 12 Poles and 6 Pole-pairs. The Resolver MCR605 Speed: 6-speed (so 6 pole-pairs) Excitation_Voltage: 7Vrms Excitation_Frequency: 10kHz The “respolepairs=1” found in link Wiki that the sin...

Doesn’t spin in both direction with up to -50A to 50A on a manual run, i make a video with Angle plot for Resolver signal, is it looking ok? my brother rotate the motor via driveshaft of the rear axle of Peugeot 508(407) hybrid. I read the Wiki link above, test many syncofs (also= 32767)but motor on...

Hi, today after 3-4 hours working found that motor is not spin, i post the video because i can’t make photo, try to spin but have noisy vibration… What to do now, please help
me.

Yes, the motor spin with -25, -45 A but show message OVERCURRENT when try to spin via throttle

I try 3 times to restart it off/on the vcu

After lower the udcsw to 100v show RUN and the 220v bulb rise up with -10A BUT PRECHARGING stay

Hi, The motor is on a bench PMSM Bosch SMG 180/120 with resolver with Toyota Prius Gen 2 and Openinverter PCB of course!! 3 times watch the Video tutorial for FOC https://m.youtube.com/watch?v=1SlL6cEoRBg I do everything as a Johannes and D. Maguire said in video, but when try to Test the motor NOTH...

Thank you very much

It's really bad news, if you use normal clutch the problem will return quickly, may be if you use C3 new bearings, Would someone tell me is that correct wire diagram on my Gen2 inverter? which pins are need to use for resolver

i don’t know but may be use only pin 1 and 4

Lovely, now i try to find good condition Gen2 invertor and need to buy the invertor controller board from openinverter.org, thank you for information!!!!

Sorry about a wrong name, thank you very much i will do it . Cheers

I just want to say thank you on Johansen(Johu), Pete9008 and MattsAwesomeStuff, with their help we were able to find out what the engine is, my PMSM motor bosch SMG 180/120 i will use with inverter from Toyota GEN 2 with a logic board of openinverter.org at 144 volts, the motor is with The Resolver ...