Updated python to version 3.11.2, but it didn't help. Then I typed "sudo apt install python-is-python3" and everything worked.

It worked! Thank you so much for your help.

It didn't work out. The nvic.h file is missing again. den@den-TM1703:~/stm32-sine-4.97.R/stm32-sine $ git tag validation/v4.97.R M libopencm3 M libopeninv Note: Switch to "tags/v4.97.R". You are now in the "disconnected pointer HEAD" state. You can look around, make experimental ...

I have sorted out this problem. The OVER CURRENT error was caused by a high level on the pwm inhibit pin (PB12). It receives +5V from the inverter. As a temporary solution, I soldered R82 and R59, thereby breaking the chain between the IGBT connector and stm32. Despite this, the OVERCURRENT error di...

Excuse me, how do I do it right? I tried typing "make git clone -deps" and another combinations with "git clone". Did "git clone" libopencm3 and libopeninv from github, but received compilation error messages "no such file directory" and another errors and war...

I am trying to compile the firmware and get an error message image.png "fatal: git repository not found (or one of the parent directories)" How to fix it? Can anyone compile the 4.97-FOC firmware with the PB12 Pull down pin (PWM INHIBIT pin) or provide a working link to the opencm3 and ope...

I have a problem with the Yaris/Auris inverter board version: small board V1 d. When I turn on the power and try to start I get an overcurrent error message. The inverter does not start in manual mode. If you repeatedly press the physical start button, the board starts with an overcurrent error, but...

I installed linux and was able to compile. Thank you! All my attempts to do this in windows turned out to be useless.

I'm trying to figure out how to compile the firmware, but I can't. What you need to open and where to typing "make"? I tried to build it in Code::Blocks but it doesn't work.

I tried to build sw and got issue
"Execution of 'CONTROL=SINE make' in 'C:\Users\.....\stm32-sine-5.24.R' failed."
What I doing wrong? I installed arm-none-eabi toolchain and set it in to toolchain executables

Oh I thought sin sw was only for induction motors and can't be used for synchronous motors. Thank you!

Is it possible to get foc firmware source code? This would solve my problem with a broken pin if pull-downed it in to gnd.

I designed the board myself. Soldering is in order and there are no short circuits. I checked pin 58 (start) and it turned out that it was not working. It seems that the matter is in the stm32 itself. In the web interface, the board is defined as Prius

I didn’t say correctly, on pins pwm3_p and pwm2_p there is a PWM, on others there is nothing

I use a diy board assembled according to the Auris / Yaris V2B4 inverter circuits. Firmware version 5.24R-foc. The "stop the inverter" button in the web interface does not stop the inverter. I tried to download the software through the web interface, but it gave an error. I also checked wi...

Hi
Help me please with problem
Din_start always “On” but stm32 pin 58 (MG2 start) has 0V
How to fix it? I can’t save parameters because board always run and can’t stoped

Hi all. Help me with the question. If you run mg1 and mg2 in parallel on the inverter and connect it to one electric motor, will it work? Or is it possible to connect only 2 electric motors separately? Inverter Toyota Aqua nhp10

thanks for the information

Hello everyone, I want to run the inverter from nissan leaf on the can bus without altering the inverter itself and use it to run the rear motor from the lexus rx400h, will this work? Or it works only with Nissan leaf motor?