More fotos please.

Applied 309V DC to the inveter but in Savvycan is only 154V? Why?

dimonlipko wrote: ↑Sun Apr 14, 2024 1:07 pm Yes, I can make CAN BUS log from my M3 with fresh software.

I would appreciate it.

I wired the VCSEC with Vehicle can bus of the drive unit and nothing happened like I had guessed before. Need help. Maybe can logs from fresh M3/Y?

Hello. Now I have a 3D7 drive unit, "go" pedal, keycard and matching VCSEC from the 2023 Tesla MY. 20240410_213952.jpg Today I've checked, how the pedal works. And it works fine. Screenshot from 2024-04-10 21-47-28.png Tomorrow I want to connect the VCSEC module to the vehicle can bus of t...

Does anyone know pinout of these contactors?

Hm... You could use such PSU as stabilized source. I would suggest that you use this solely for determining if precharge works correctly or of the motor spins unloaded. I would advise against using this for driving motor under any kind of torque. https://openinverter.org/forum/viewtopic.php?p=8196#...

Surely, it is no secret to many that in an ATX computer power supply there is 320 volts of DC voltage running on a large filter capacitor after the diode bridge. It is known that the diode bridge is not very powerful - only 6 amps. Now the question. Is it safe to use such a power supply to spin the ...

Where is the video of driving?

Do you have a dragy? Could you floor it and show the numbers?

What are the chances that the pyrofuse didn't break 2 phases in the inverter of 3D7 motor whose rear mount was torn off?

Does anyone know if there have been any recalls for these batteries? Are they generally reliable?

I have the possibility to buy a 3D7 motor from MY 2023 for 800 euros with a broken rear mount. Is this a good price? How to check it with a multimeter for broken mosfets? Or are there no problems with inverters in this generation of motors?

Are flexible brake lines a reliable solution?

jrbe wrote: ↑Fri Jan 12, 2024 12:15 am Have you found any info on it's power capabilities?

The same as 530e 26 Ah pack.

Max. power (discharge) 83 kW (short-term)

According to this table does it mean that 3D7 has a "full mosfet" inverter? Not like old 3D5 without 3 mosfets?

MattsAwesomeStuff wrote: ↑Mon Jan 08, 2024 8:33 am ... I would absolutely abusively take advantage of this relationship. Kidnap and interrogate him

So many questions.

If someone has linkedin please contact him. I don't have access to private messages there. https://pl.linkedin.com/in/filip-kossakowski-6270a6153

Is this a part of the code in the booster, a recommended mechanical spec, or an error? You have to be careful preloading a brake master cylinder. At some travel point it blocks the port to the brake fluid reservoir. This means as the brakes / fluid heat up the system builds pressure when there shou...

20240107_224626.jpg 20240107_224808.jpg Today I discovered that the master cylinder is preloaded about 1 mm by default without any power being applied to the ibooster. So it means that preloading the push rod isn't a bad idea. It has a little free play which is needed for the calibration of the tra...

Screenshot from 2023-12-24 17-51-45.png Today I tried to preload the push rod slightly by hand. And guess what? ibooster is not "clicking" now.  I don't know what exact position of rod is needed but I think I'm on the right way. Is it normal when the push rod is preloaded? Idk how it is o...

Does it then provide assistance for a little while and then stop again, or does it not provide assistance at all and just pulses the lock/unlock of the system? You tried pulsing the 12V line for it to unlock and then see it it "times out"? It is possibly looking for a vehicle terminal sta...

tom91 wrote: ↑Sat Dec 23, 2023 10:49 am Does the Ibooster "unlock" when you give it 12V ignition Pin 20? As in you hear it move the motor and it draws more current.

Does it transmit any CAN on the CAN bus at 500kbps? Ofcourse with it terminated at 2x120 ohm.

yes and yes

After failing to find any scrapper willing to sell me the plug for less than $100, including employees saying "If he can't make 4000% markup he'd rather have it shredded, he's a moron.", I ordered most of a set from Chief Enterprises. Got the main plug, the clip housing, and several of th...

Here is wiring diagram. iboosters for peugeot/citroen does not have dual can.

Which car is this from an Citroen Hybrid? How is it behaving? The Renault one just needs a can transceiver on the YAW can, I just used an Arduino Due doing GVRET and savvy CAN for bench testing. It is from ds7. It works immediately when power is applied to the wake up pin. Makes assist and so on bu...