I already understood the problem. At the stage of checking the welding of contactors, I get an error. I plan to use power contactors, so now I have installed 2 15 ohm 10 watt resistors instead. Apparently they don't like lim.

Hello. Tell me please, should the contactor test run during each charging session? I don't get it. And in byte 2, 00 immediately appears when LIM is turned on.
I already got a new Lim. But I have the old problem in the form of a flashing red LED when switching to 3E9,8,08,52,11,00,00,00,00,00,

I wonder what lim 2018 will tell me. I will get it soon.

EV_Builder wrote: ↑Mon Jan 02, 2023 7:59 pm Maybe there wan't more available?

160a is available at the station.

I doubt the lim 2014 will pass more than 125a. Today I received a message on the I'd 29e. The maximum capabilities of the station were reported as 125a. Although I charge my Tesla on it with a current of 160A.

I've seen this with other CCS implementations as well. The fact that AC charging works can still mean CCS does not. It can even vary from charger to charger. Is your CP line nice and short? Thinking out loud: would it be possible / helpful to shield it? You cannot twist CP and PE as a pair, but per...

Don't know your situation offcourse but make sure the plug is fully inserted in ccs. I mention because it's bulky and we often squeeze it in the filler place. The connector is inserted normally, there is also 5% pwm. Because I see it 3B4,8,00,FF,31,F0,BC,FF,00,00, . I'm already tired. But ordered a...

Alot, specially since you wrote your own code. I would say compare your own logs to known working ones, this is the only way to diagnose it. Also a chance that you are using an incompatible LIM with a CCS charger that outputs a not supported protocol (unlikely). I already compared can protocols, ev...

Fix your wiring, as it needs to duplicate the BMW I3 implementation. Easiest to get this working is using a type 1 AC charging to start. It does determine that a CCS is present due to 5% pilot yet it has errors for plug. image.png image.png AC charging starts without complaint. DC charging never st...

Thank you. I will continue tomorrow.

Maybe I missed one point:
1. I have lim...646 USA.
2 Port duoside. I did not put the 620 ohm resistor. Between GND and CP. Could this be the reason for my failure?
But my lim reacts normally to the connection.
3B4,8,00,FF,31,F0,BC,FF,00,00,

I get to this level 3B4 8 00 FF 31 F4 BD FF 04 00 . But, before that, at the moment LIM gets 3E9: 8,08,52,11,00,00,00,00,00, the red LED immediately starts flashing. I'm paying for the charging station, but the insulation test did not start. The problem is the blinking LED. I'm doing something wron...

You are not getting a valid Charging_Type in 0x3B4, Byte 6 and thus it hangs/remains in Initlialisation. I get to this level 3B4 8 00 FF 31 F4 BD FF 04 00 . But, before that, at the moment LIM gets 3E9: 8,08,52,11,00,00,00,00,00, the red LED immediately starts flashing. I'm paying for the charging ...

Hi all. Today I tried to run my VCU for LIM for the first time. But unsuccessfully. When transitioning to lim_state 2, the red LED begins to flash. Checked the Flap, it is in position 1. Locking the port in the LOCK position (11k). What can be wrong? Capture of the сan in the attachment. Thank you.

Thank you.sometimes you can get lost in elementary things)

Yes, I use normal length. It's also not entirely clear to me what soc is here. For example, in the logs posted on GitHub.
112,8,FA,1F,16,0E,F6,70,15,5A,
If it is not difficult for you, you can explain with an example.
Thank you.

Hi to all. I'm finishing my program for Lim 2014. I studied the logs taken from the car BMW i3 2014. I can't figure out how SOC_local is defined here. I'd 0x112, byte 4.5. I get some big numbers. Can someone explain why?

There are different types of TLV6001. With the "R" version, pin 5 = V-, pin 2 = V+. Without "R" it's the other way around. With the "U" version, the inputs and outputs are different. is it possible to install id instead of rid? By changing the polarity of the power sup...

tom91 wrote: ↑Sun Nov 13, 2022 12:32 pm Please do this if you need help, you are saying you get to a certain point in the sequence so there will be clues.

For now, I took a break, remaking my Arduino controller. At stm 32. When I'm ready, I'll definitely show my capture . I'm learning now cubeIDE .

muehlpower wrote: ↑Sun Nov 13, 2022 2:21 pm There are different types of TLV6001. With the "R" version, pin 5 = V-, pin 2 = V+. Without "R" it's the other way around. With the "U" version, the inputs and outputs are different.

Thank you.

Hello. Is there an error in the voltage meter circuit? By connecting the polarity of the power supply TLV 6001 ?

Did you notice that the proxy has to be connected to pins 2 and 6 on USA models? BTW, US and EU LIMs are the same and can be recoded. I paid attention to it. I bought the lim together with wires and a conectors. Do I need to put an additional jumper between 2 and 6? Because now there is no connecti...

Ok. Thank you.

Hello everyone, help to solve the problem. I have a lim 2014 USA.(...646) The welding test passes normally. I see. 272,false,Rx,0,8,33,F3,01,11,FF,FF,FF,FF, Then I connect the connector of the charging station, the LED starts to glow yellow. 3B4,false,Rx,0,8,00,FF,31,F0,BC,FF,00,00. Everything seems...