Hello does anyone have part number for this black connector? Attached to Wemos mini D1 adapter board. Screen Shot 2023-03-07 at 1.39.09 PM.png It could simply be a WiFi issue. If you using the Omilex WiFi module I suggest you switch to the Wemos mini D1. See this post from Damien https://openinverte...

Very Simple question about Zombie VCU, after applying -12V pin 55 and +12V pin 56; Enter wifi setting Enter 192.168.4.1 The independent parameter boxes do not show up, after powering down for 10 days, the parameters will randomly show up. But when resetting they vanish never to be seen again. Did th...

We retained transfercase and attached a GS450h gearbox to it. Removed OE gearbox shaft that mates to transfercase, you'll need to operate on the gearbox. Next we modified the GS450h driveshaft with rubber mount. Just after the rubber end, where here is meat to the drive shaft, the OE splined end was...

Impressive and super informative video!
You've confirmed that wiring to MG1 is not necessary at all.

Is it possible to run MG2 motor without making any connections to MG1, would like to physically remove it.

They are pictured above in a test block with 35mm² shielded cable on the left and a 50mm² unshielded cable on the right which both form a tight fit. You have 35mm2 (2 AWG) and 50mm2 (1/0 AWG) cable. If I recall correctly the original shielded cable was something like 20mm2 (4 AWG) of copper. What i...

Mr. Bauer, I tip my hat to you! For bypassing the boost capacitor bank we are not using the OEM connector: POSITIVE (+) HV DC is on the LEFT | NEGATIVE (-) HV DC is on the RIGHT GS450h DC Link (+) and (-).jpeg

Greetings EV World. In Damien's last video he mentions making the HV DC connections to these points in the GS450H inverter and not the OEM location, from the previous Prius inverter videos, was under the impression that was only for Prius Inverter only. https://vimeo.com/742398661 Can someone confir...

Logs from conn2 & ext. North American 2018 Model 3 (First day reservation holder - Destroyed within 1st month 2000km)

What is the minimum DC pack voltage needed for testing functionality? According to V3 parameters min battery is 50V. Set the max voltage for the charger to a conservative lower number this is to verify the charger is functional. Once you verify that it functions as intended, set the normal charge v...

Mr. J Bauer (Damien), we LOVE your work, you're a catalyst for the EV conversion community. We will look into the CAN capture to see if we can find anything and learn along the way. Thank you for responding, intention is NOT to stress you, or have you finish our project over others, we are aware of ...

Is there a way we can look at the source code, and do some troubleshooting from our end vs being idle and waiting?

Our NA Spec PCS has been on standby, waiting for a shipping address, did the PM thing and nothing.

Anyone have an extra V1 or V2 board for sale, need one fast!

We have controller board v3 and it did not boot up the PCS. Board was sent 109 frames, it did not respond. The 109 and 108 controller replies did not correspond. We also observed board's IPC CAN msgs were sent over EXT CAN. On the github, the software wasn't supposed to send IPC and EXT msgs on same...

I have offered to anyone with a non working pcs and controller to send it over to me here in Ireland I have a Model 3 PCS on the bench, PM an address and will gladly ship out. Looking forward to having the charger saga operational. :D EXT CAN was soldered on 1st board, CP CAN was not soldered, upon...

WhatsApp Image 2022-07-28 at 5.22.35 PM.jpeg Before shipping, quick question about the 4 double Rabbit Teeth that are by this writing, please explain this process as its not in the other versions. SOLDER FOR CP CAN SOLDER FOR EXT CAN Also on this charger we can set the maximum charge voltage, but w...

Put this magical document together by using information from posts, my last post had CANbus wires on 34 & 35 mixed up. Attached original V3 document from Damien's repository.

Using a North American 2018 Early released charger, and it's not functional using V3 board.

PCS controller up and running and connected to web interface Cannot find a network to connect 192.168.4.1, tried using CAN wires nothing. Get red blinking lights, green light on wifi blinks quick only when turning on. Looked at videos did not find instructions on entering program screen. What is be...