Search found 5828 matches
- Sat May 11, 2024 3:35 pm
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 53
- Views: 2162
Re: First-Time Config of FOCCI And CCS1 vehicle charging
Yes, that would require much more RAM text data bss dec hex filename 683952 2112 154504 840568 cd378 stm32_ccs Solution would be either try to butcher some redundant stuff or bigger MCU like https://www.digikey.de/de/products/detail/stmicroelectronics/STM32U575RIT6Q/18085716 or https://jlcpcb.com/pa...
- Fri May 10, 2024 5:59 pm
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 53
- Views: 2162
Re: First-Time Config of FOCCI And CCS1 vehicle charging
For Precharge TargetVoltage isn't used but BatteryVoltage. Is that mapped correctly?
- Fri May 10, 2024 5:57 pm
- Forum: General
- Topic: Big-Endian CAN mapping
- Replies: 2
- Views: 140
Re: Big-Endian CAN mapping
Hmm, the bit order shouldn't be changed at all, just the byte order: word = (bptr[0] << 24) | (bptr[1] << 16) | (bptr[2] << 8) | bptr[3]; I think it should be consistent with SavvyCAN that the position now specifies the "end" of the data item. So little endian bit 0, length 16 becomes big ...
- Fri May 10, 2024 2:53 pm
- Forum: User Interface
- Topic: Save parameters to flash returns ok but params not stored.
- Replies: 4
- Views: 356
Re: Save parameters to flash returns ok but params not stored.
Forgot the obvious: when the inverter is in Run mode it won't save (because it interrupts the control loop). It must be in stop mode. The CAN Ui doesn't report this yet...
- Thu May 09, 2024 9:48 pm
- Forum: Classifieds
- Topic: FS: Nissan CHAdeMO port and CHAdeMO plug EVSE side - price lowered!
- Replies: 8
- Views: 909
Re: FS: Nissan CHAdeMO port and CHAdeMO plug EVSE side - price lowered!
Hmm, not sure. It's the Nissan cable 296B1-3NF1A
I assume 35mm² or 50mm². I can only measure cable diameter. Used to charge at 180A on Aral Pulse
I assume 35mm² or 50mm². I can only measure cable diameter. Used to charge at 180A on Aral Pulse
- Wed May 08, 2024 6:22 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter looses WiFi connection when trying to update
- Replies: 5
- Views: 277
Re: Zombieverter looses WiFi connection when trying to update
The latest web ui hides SWD update as it only works with additional connections. And even then it never really worked for me
UART may fail but in that case you can power cycle and retry
UART may fail but in that case you can power cycle and retry
- Wed May 08, 2024 7:48 am
- Forum: User Interface
- Topic: Update via wifi fails
- Replies: 32
- Views: 10841
Re: Update via wifi fails
Indeed the bin files don't really need to be kept. When uploading a new one all existing ones could be deleted. The javascript fix has the advantage for now that the module doesn't need to be upgraded with special tools but just by uploading the .js file Next issue is possibly the json files that ar...
- Tue May 07, 2024 9:26 pm
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 53
- Views: 2162
Re: First-Time Config of FOCCI And CCS1 vehicle charging
I think the 5% PWM should start as soon as the charger is powered and you have 2k7 pull-down to PE (not PP). When you say "PP" do you mean "PE" i.e. Earth? Doesn't really make much sense to measure between CP and PP
- Tue May 07, 2024 9:24 pm
- Forum: Nissan
- Topic: Nissan Leaf Gen3 Drop-in board
- Replies: 41
- Views: 3213
Re: Nissan Leaf Gen3 Drop-in board
Maybe I get a chance to test with Zoe motor
- Tue May 07, 2024 12:29 pm
- Forum: Getting Started
- Topic: where to pass TUV in Germany
- Replies: 40
- Views: 12221
Re: where to pass TUV in Germany
The last time I went was with Audi A2. But that was first registered in 2001 so before that threshold date. Anyway, Touran is from 2004 and back then I emailed Klaus Baumeister of TÜV Nord (unfortunately he is retired now) ... Nun möchte ich wieder einen Umbau machen, diesmal jedoch mit Serienkompon...
- Tue May 07, 2024 8:05 am
- Forum: Projects
- Topic: [DRIVING] VX220 with Tesla SDU
- Replies: 143
- Views: 19324
Re: [DRIVING] VX220 with Tesla SDU
With firmware 5.27.R you can freely map "regenpreset" to CAN. It is 0-100% * offthrotregen
- Tue May 07, 2024 7:10 am
- Forum: Toyota/Lexus
- Topic: Unwanted "over current" messages Prius20
- Replies: 7
- Views: 514
Re: Unwanted "over current" messages Prius20
Wait, I had this yesterday also. Can you put the latest firmware on the ESP module
https://github.com/jsphuebner/esp8266-web-interface
https://github.com/jsphuebner/esp8266-web-interface
- Mon May 06, 2024 7:27 pm
- Forum: General
- Topic: Improve documentation with help of AI
- Replies: 4
- Views: 265
Re: Improve documentation with help of AI
Exciting!
What options do we have? Is there AI that generates formatted output, maybe even draws diagrams that we can put directly into the wiki?
What options do we have? Is there AI that generates formatted output, maybe even draws diagrams that we can put directly into the wiki?
- Mon May 06, 2024 6:38 pm
- Forum: User Interface
- Topic: Update via wifi fails
- Replies: 32
- Views: 10841
Re: Update via wifi fails
Finally put Janosches fix in place
https://github.com/jsphuebner/esp8266-w ... 47da6fa7c5
https://github.com/jsphuebner/esp8266-w ... 47da6fa7c5
- Mon May 06, 2024 7:14 am
- Forum: Tesla
- Topic: Using iBooster Brake Pressure Sensor with LDU Board
- Replies: 1
- Views: 201
Re: Using iBooster Brake Pressure Sensor with LDU Board
I suppose the iBooster also communicates pedal travel via CAN?
Then you can map that to "regenpreset" when using 5.27.R firmware
There is also a secondary throttle input that can be used as regenpreset source
Then you can map that to "regenpreset" when using 5.27.R firmware
There is also a secondary throttle input that can be used as regenpreset source
- Mon May 06, 2024 5:37 am
- Forum: Nissan
- Topic: Nissan Leaf Gen3 Drop-in board
- Replies: 41
- Views: 3213
Re: Nissan Leaf Gen3 Drop-in board
Maybe add resolver to pinswap?
- Sun May 05, 2024 5:41 pm
- Forum: Projects
- Topic: 2008 Corvette C6 Conversion
- Replies: 9
- Views: 4124
Re: 2008 Corvette C6 Conversion
Yes like a valave it tapers down
- Sat May 04, 2024 7:26 pm
- Forum: Classifieds
- Topic: WtB: DFSK/MG 3-phase Charger
- Replies: 13
- Views: 1542
Re: WtB: DFSK/MG 3-phase Charger
It was found here: http://www.bildelsbasen.se/
I payed roundabout 500€ delivered from Sweden
Now I'm searching for the plugs which turns out harder than I thought.
Part numbers HVC5P63FSX06 (input) and HVC2P28FSX04 (output)
I payed roundabout 500€ delivered from Sweden
Now I'm searching for the plugs which turns out harder than I thought.
Part numbers HVC5P63FSX06 (input) and HVC2P28FSX04 (output)
- Fri May 03, 2024 6:13 pm
- Forum: Classifieds
- Topic: FS: Nissan CHAdeMO port and CHAdeMO plug EVSE side - price lowered!
- Replies: 8
- Views: 909
Re: FS: Nissan CHAdeMO port and CHAdeMO plug EVSE side - price lowered!
Lowered price to 70€
- Fri May 03, 2024 6:12 pm
- Forum: Classifieds
- Topic: WtB: DFSK/MG 3-phase Charger
- Replies: 13
- Views: 1542
Re: WtB: DFSK/MG 3-phase Charger
Got the 11 kW one from Sweden
- Fri May 03, 2024 4:40 pm
- Forum: Toyota/Lexus
- Topic: Unwanted "over current" messages Prius20
- Replies: 7
- Views: 514
Re: Unwanted "over current" messages Prius20
You can download a preliminary binary here: https://github.com/jsphuebner/stm32-sin ... 8942103986
- Fri May 03, 2024 10:01 am
- Forum: Charging
- Topic: Type 2 to CHAdeMO Converter/Charger?
- Replies: 3
- Views: 374
Re: Type 2 to CHAdeMO Converter?
You can't really call this a "converter" it is rather a full blown charger that converts AC to DC power using power electronics.
https://de.aliexpress.com/item/1005005817982041.html
I built something like that in the past: viewtopic.php?t=763
https://de.aliexpress.com/item/1005005817982041.html
I built something like that in the past: viewtopic.php?t=763
- Thu May 02, 2024 7:12 pm
- Forum: Battery Managment (BMS)
- Topic: Switched ADC BMS
- Replies: 185
- Views: 37668
Re: Switched ADC BMS
Dont we love it when the reaction to an announcement is yet another request You're welcome...
I've added a workflow that builds binaries on every commit https://github.com/jsphuebner/FlyingAdcBms/actions
I've added a workflow that builds binaries on every commit https://github.com/jsphuebner/FlyingAdcBms/actions
- Thu May 02, 2024 7:03 pm
- Forum: Toyota/Lexus
- Topic: Unwanted "over current" messages Prius20
- Replies: 7
- Views: 514
Re: Unwanted "over current" messages Prius20
I think I will include this in the next release. Had similar issues and created a FW on the fly that ignores the input and just keeps going. Runs fine.
- Thu May 02, 2024 6:17 pm
- Forum: User Interface
- Topic: Save parameters to flash returns ok but params not stored.
- Replies: 4
- Views: 356
Re: Save parameters to flash returns ok but params not stored.
I'm assuming this is related to your other post?