Okay, then my proposal is: At startup of the esp:
If numberOfBinFiles>1 then deleteAllBinFiles()
This keeps a single file forever, and cleans up multiple ones.
Search found 629 matches
- Wed May 08, 2024 7:50 pm
- Forum: User Interface
- Topic: Update via wifi fails
- Replies: 32
- Views: 10725
- Wed May 08, 2024 5:01 pm
- Forum: General
- Topic: Save parameters to flash returns ok but params not stored.
- Replies: 3
- Views: 286
Re: Save parameters to flash returns ok but params not stored.
From my understanding there are two classes of parameters: one is stored in flash, the other is volatile. Maybe you try to store a volatile parameter. Or does the issue happen for all?
- Wed May 08, 2024 7:28 am
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 39
- Views: 1753
Re: First-Time Config of FOCCI And CCS1 vehicle charging
Just to be sure, "sharing the same PE" means, that the following signals are together: - Ground of Foccci - Ground of the 12V supply that feeds Foccci - PE of the CCS socket - minus of the multimeter if you measure the PP voltage on car side (around 4.5V if nothing is connected). - ground ...
- Wed May 08, 2024 7:10 am
- Forum: User Interface
- Topic: Update via wifi fails
- Replies: 32
- Views: 10725
Re: Update via wifi fails
Regarding the topic "ESP file system gets full due to multiple bin files", I understand that one fix is to delete the bin file after successful update. The above commit implements this fix in the javascript, means: in browser. Right? This helps in case of successful flashing, but for the u...
- Wed May 08, 2024 5:47 am
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 39
- Views: 1753
Re: First-Time Config of FOCCI And CCS1 vehicle charging
Yes, there seems to be confusion with the pins. There are three: 1. The PE, protective earth, chassis ground. This needs to be connected to the ground of Foccci. This is the reference point for your multimeter. The single 6mm pin in the center. 2. The CP. Control pilot. This needs to be connected to...
- Tue May 07, 2024 8:18 pm
- Forum: Classifieds
- Topic: Tesla with damaged rear side available in Ingolstadt
- Replies: 1
- Views: 297
Re: Tesla with damaged rear side available in Ingolstadt
The dealer announced it here https://m.mobile.de/auto-inserat/tesla- ... 8c&type=ad
Quite expensive, 30k euro for such a broken car.
Quite expensive, 30k euro for such a broken car.
- Tue May 07, 2024 5:52 am
- Forum: Charging
- Topic: Drawing power out of CCS port (V2x, inverse charging, bidirectional CCS)
- Replies: 41
- Views: 19732
Re: Drawing power out of CCS port (V2x, inverse charging, bidirectional CCS)
In a comment to the video ( we got a confirmation from mizettelzettel that pyPLC together with 350V physical voltage convinced a Tesla model 3 to close the contactors, and drawing 4kW over 30mins was working without error.
- Mon May 06, 2024 7:22 pm
- Forum: Charging
- Topic: Open source CCS using AR7420
- Replies: 420
- Views: 299893
Re: Open source CCS using AR7420
No, the coordinator setting cannot be changed by the car, and also pyPLC does not touch this. It is only changed by writing a PIB. At least I see no other way.
"Always" is the correct CCo setting for the Evse.
"Always" is the correct CCo setting for the Evse.
- Mon May 06, 2024 6:44 pm
- Forum: Projects
- Topic: 1984 Voltswagen Rabbit Prius Gen 3 ZOMBIE
- Replies: 409
- Views: 31655
- Mon May 06, 2024 6:43 pm
- Forum: General
- Topic: Improve documentation with help of AI
- Replies: 4
- Views: 251
Improve documentation with help of AI
As @jrbe proposed, we could try to improve the docu using AI. This thread is intended to discuss the possibilities and the results.
Any Idea welcome.
Any Idea welcome.
- Sun May 05, 2024 9:41 am
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 39
- Views: 1753
Re: First-Time Config of FOCCI And CCS1 vehicle charging
To cover the typical mistakes "CP and PP mixed up or not wired" just added hints in the trouble-shooting chapter: https://github.com/uhi22/foccci#no-comm ... r-possible
- Sat May 04, 2024 9:41 am
- Forum: Charging
- Topic: Type 2 to CHAdeMO Converter/Charger?
- Replies: 3
- Views: 371
Re: Type 2 to CHAdeMO Converter/Charger?
Could the following concept work: - for the high-power stuff use a 22kW charger from a car. This takes 3 phase AC and provides HV DC. I think Damien reverse-engineered a MG charger which seems to be controllable via CAN easily. - into the type 2 direction, use an Arduino which measures the CP PWM an...
- Sat May 04, 2024 8:54 am
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 39
- Views: 1753
Re: First-Time Config of FOCCI And CCS1 vehicle charging
To simplify trouble shooting the CP and PP lines, added ResistanceProxPilot to the serial logging. If the charger is plugged in, we should see something like cpDuty [%] 5 ResistanceProxPilot [ohm] 1495 The CP PWM duty cycle should be between 4 and 6 percent (5% nominal), and the PP resistance betwee...
- Fri May 03, 2024 7:05 pm
- Forum: Classifieds
- Topic: Tesla with damaged rear side available in Ingolstadt
- Replies: 1
- Views: 297
Tesla with damaged rear side available in Ingolstadt
On my daily way, I see a Tesla M3 (or Y?) at a "dealer". It has quite some crash impact on the back, but I think a lot of parts are still in a good shape (battery, drive unit). It is sitting there since weeks. Personally I do not have plans, but if anybody is interested, maybe it is possib...
- Fri May 03, 2024 6:57 pm
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 39
- Views: 1753
Re: First-Time Config of FOCCI And CCS1 vehicle charging
Also wondering if this is a change I may have to make. I found these bits of doc in the CCS1 protocol documentation and it seems that in a certain setup, 4.7k is optional? There are two different use cases: CCS type 1 and CCS type 2. The upper picture, with Rs3 and Rs4 and button in the connector, ...
- Fri May 03, 2024 6:38 pm
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 39
- Views: 1753
Re: First-Time Config of FOCCI And CCS1 vehicle charging
Does the charger provide 12V between CP and PE if just sticking the multimeter probes into the CCS plug?
- Fri May 03, 2024 6:36 am
- Forum: Charging
- Topic: Open source CCS using AR7420
- Replies: 420
- Views: 299893
Re: Open source CCS using AR7420
1. At room temperature, after running some minutes, my AR7420 is around 52°C (measured with infrared thermometer). Touching with the finger is okay for 10s, then it hurts. If yours is much hotter, just use a new one. Maybe killed by overvoltage or something. 2. I see no error in your original.pib. I...
- Fri May 03, 2024 5:17 am
- Forum: Battery Managment (BMS)
- Topic: Switched ADC BMS
- Replies: 184
- Views: 37319
Re: Switched ADC BMS
The plan is, that the bin and hex files are available at the link https://github.com/jsphuebner/FlyingAdcBms/actions How does this work? Johu configured a "continuous integration job" to the github. This job automatically builds the software and stores the results. Each run is listed on th...
- Thu May 02, 2024 8:17 pm
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 39
- Views: 1753
Re: First-Time Config of FOCCI And CCS1 vehicle charging
The logs are saying all the same: No response from charger. The SOC does not matter at this stage. Any chance to measure the CP PWM, in the web interface and with an oscilloscope?
- Thu May 02, 2024 7:34 am
- Forum: VW (VAG, Volkswagen, Audi, Porsche etc.)
- Topic: MLBEvo DBC & LIN Files
- Replies: 18
- Views: 5120
Re: MLBEvo DBC & LIN Files
The "conversion" of your findings into a DBC file is indeed a manual process. You found out, e.g. for Lamp1, which CAN ID and which bit in this message controls the lamp. This information you put manually into the data base file (dbc). You can do this with the DBC editor which is included ...
- Tue Apr 30, 2024 7:15 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter / leaf gen 2 newbee questions
- Replies: 4
- Views: 60623
Re: Zombieverter / leaf gen 2 newbee questions
Do you plan to have isolation between the CAN and the shunt terminals?
- Tue Apr 30, 2024 4:32 pm
- Forum: Charging
- Topic: First-Time Config of FOCCI And CCS1 vehicle charging
- Replies: 39
- Views: 1753
Re: First-Time Config of FOCCI And CCS1 vehicle charging
Great. In case you are charging (or run into trouble) it would be nice to provide a logfile, and the charger type if possible.
- Tue Apr 30, 2024 5:30 am
- Forum: Charging
- Topic: QCA7000 Foccci+Clara User thread
- Replies: 30
- Views: 2209
Re: QCA7000 Foccci+Clara User thread
Great. I just used a random ID, for me it does not matter.
- Mon Apr 29, 2024 5:06 pm
- Forum: User Interface
- Topic: Use ESP32 Web interface also as GVRET CAN device?
- Replies: 47
- Views: 2992
Re: Use ESP32 Web interface also as GVRET CAN device?
Using the bus number 3 the transmitting works. This number is also shown in the main window. Not sure why it is number 3, but at least it works.
- Mon Apr 29, 2024 9:53 am
- Forum: Charging
- Topic: Drawing power out of CCS port (V2x, inverse charging, bidirectional CCS)
- Replies: 41
- Views: 19732
Re: Drawing power out of CCS port (V2x, inverse charging, bidirectional CCS)
One topic to improve in pyPLC, maybe this improves the Tesla behavior: We are sending in the PreChargeRes "EVSEStatusCode_text": "EVSE_NotReady". The alpitronic and the supercharger are sending "EVSEStatusCode_text": "EVSE_Ready" [Edit] Pushed the fix: https:/...