Search found 220 matches
- Fri May 10, 2024 5:34 am
- Forum: Getting Started
- Topic: ZombieVerter VCU Connector Depinning Tool
- Replies: 11
- Views: 418
Re: ZombieVerter VCU Connector Depinning Tool
Best to use the pinout from the wiki as I corrected the can and can2 positions. Older posts on the forum may have this incorrect.
- Wed May 08, 2024 6:07 pm
- Forum: Vehicle Control (VCU)
- Topic: Cannot initialise Isa shunt through Zombieverter
- Replies: 8
- Views: 148341
Re: Cannot initialise Isa shunt through Zombieverter
If you are following the connection diagram on the wiki this will not be the problem as it has since been corrected.
If you have SavvyCAN a log from the shunt and initialisation would be useful.
If you have SavvyCAN a log from the shunt and initialisation would be useful.
- Wed May 08, 2024 5:10 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombie and GS450H connected but no spin
- Replies: 7
- Views: 156965
Re: Zombie and GS450H connected but no spin
As you are running without a shunt, as well as setting udcsw to 0V you also need udcmin set to 0V otherwise the torque setting will be 0.
- Tue May 07, 2024 11:04 pm
- Forum: Vehicle Control (VCU)
- Topic: PWM servo drive from zombieverter: possible?/code snippet? /instuctions?
- Replies: 1
- Views: 254
Re: PWM servo drive from zombieverter: possible?/code snippet? /instuctions?
PWM1_OUT, PWM2_OUT, PWM3_OUT may work. They are 12V outputs so may need a resistor divider to get to the correct voltage. I haven't tested with a servo but have measured the frequency and tested with a LED. Select PWM output for PWM1Func - PWM3Func in General Purpose I/O Under PWM Control set the pr...
- Thu May 02, 2024 2:37 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombie not going into Run mode SOLVED
- Replies: 22
- Views: 108616
Re: Zombie not going into Run mode
Yes, as already explained in at least three posts above. You are not meeting two of the three conditions that must be met to go into run mode, as indicated by "status". Set udcsw to 0 and potmin to 500 ( i.e. >491 ) and it should work.
- Wed May 01, 2024 6:37 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombie not going into Run mode SOLVED
- Replies: 22
- Views: 108616
Re: Zombie not going into Run mode
Status has to be "none" to go into run mode. Ideally the throttle has to be connected and calibrated correctly, but may work if disconnected and potmin set to 0.
- Wed May 01, 2024 5:50 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombie not going into Run mode SOLVED
- Replies: 22
- Views: 108616
Re: Zombie not going into Run mode
If status is PotPressed then the throttle pedal calibration is not correct. potmin needs to be higher than pot by 10 - 20. If using dual pot then pot2min needs to be adjusted as well although this is not checked for going into run mode.
- Wed May 01, 2024 4:30 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombie not going into Run mode SOLVED
- Replies: 22
- Views: 108616
Re: Zombie not going into Run mode
Is status "none" or "PotPressed"?
- Wed May 01, 2024 2:51 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombie not going into Run mode SOLVED
- Replies: 22
- Views: 108616
Re: Zombie not going into Run mode
deleted as similar to above.
- Wed Apr 24, 2024 1:03 pm
- Forum: Battery Managment (BMS)
- Topic: Simp BMS
- Replies: 643
- Views: 254735
Re: Simp BMS
I tested this last year. Battery modules and Sbox clash on id 0x100 so can not share the same bus.
- Tue Apr 16, 2024 8:45 pm
- Forum: Nissan
- Topic: Leaf Gen 1 Inverter Board
- Replies: 319
- Views: 178563
Re: Leaf Gen 1 Inverter Board
That's what I would expect. The ISA shunt data is sent to Serial2 which is the wifi interface. To view it on the terminal you to need to change Serial2 to Serial, or you could copy the code so it sends to both.
- Tue Apr 16, 2024 4:40 pm
- Forum: Nissan
- Topic: Leaf Gen 1 Inverter Board
- Replies: 319
- Views: 178563
Re: Leaf Gen 1 Inverter Board
I have tested with your exact code with the } fixed and it all works. I am only sending messages to Can0 and don't have wifi so all readings are going to Serial ( I am using Arduino Due so just looking with serial monitor in IDE ). I thought it might be a timing problem as CheckCAN is polled in loop...
- Tue Apr 16, 2024 12:59 pm
- Forum: Mitsubishi
- Topic: Can you identify this Outlander item?
- Replies: 6
- Views: 685
Re: Can you identify this Outlander item?
From searches for part number this is dc to 110V AC. The dc-dc 12V converter part number TW-90 / 37129-01001, ( for heated windows ) has fans but they blow air over an external heatsink. The dc - 230V converter is also made by Toyota Industries is part number 9461A092.
- Tue Apr 16, 2024 11:32 am
- Forum: Nissan
- Topic: Leaf Gen 1 Inverter Board
- Replies: 319
- Views: 178563
Re: Leaf Gen 1 Inverter Board
There's a small error in CheckCan } if(inFrame.id >= 0x521 && inFrame.id <= 0x528 && inFrame.length == 8){ Sensor.ISA::gotFrame(&inFrame, 0); //Added by royhen99 } //////////////////////////////////////////////////////////////////////////////////////////////// } should be if(inFr...
- Mon Apr 15, 2024 11:21 pm
- Forum: Projects
- Topic: [WIP] Project Rising Sun: Suzuki SJ410k meets Leaf full stack
- Replies: 21
- Views: 5565
Re: [WIP] Project Rising Sun: Suzuki SJ410k meets Leaf full stack
0x59E, 0x55B and 0x5BC. If you look at each id one at a time it's clear that most of the messages sent are the fixed values from leafinv.cpp.
- Mon Apr 15, 2024 6:29 pm
- Forum: Nissan
- Topic: Leaf Gen 1 Inverter Board
- Replies: 319
- Views: 178563
Re: Leaf Gen 1 Inverter Board
I think I have fixed it. The isa library has is own interrupt service routine which takes priority over the routine in the main code. The modifications below fix this by calling the isa interrupt routine from the main code. I have checked with appropriate ids and data generated in Savvycan. 1) in IS...
- Mon Apr 15, 2024 10:37 am
- Forum: Projects
- Topic: [WIP] Project Rising Sun: Suzuki SJ410k meets Leaf full stack
- Replies: 21
- Views: 5565
Re: [WIP] Project Rising Sun: Suzuki SJ410k meets Leaf full stack
I have no experience with leaf PDM etc, but your code on github does not look up to date as it does not compile and has other errors. From you CAN log the zombieverter is still sending data on 3 ids which may be causing the problems. I think this is because where you have declared/defined the variab...
- Sun Apr 14, 2024 8:55 pm
- Forum: Nissan
- Topic: Leaf Gen 1 Inverter Board
- Replies: 319
- Views: 178563
Re: Leaf Gen 1 Inverter Board
Seting up the ISA shunt sets a filter on can0 that blocks the inverter can ids.
Adding the line in bold after Sensor.begin may fix it.
Sensor.begin(port,datarate);
port->setRXFilter(0, 0x100 0x300, false); // this allows ids 0x100 - 0x1FF and 0x500 - 0x5FF to pass
Adding the line in bold after Sensor.begin may fix it.
Sensor.begin(port,datarate);
port->setRXFilter(0, 0x100 0x300, false); // this allows ids 0x100 - 0x1FF and 0x500 - 0x5FF to pass
- Fri Apr 12, 2024 12:28 pm
- Forum: Battery Managment (BMS)
- Topic: BMW 330e pack balancing
- Replies: 13
- Views: 829
Re: BMW 330e pack balancing
Cell voltage readings are only valid when not balancing so they are updated every minute. The min to max cell voltage difference is checked against the "Balance Voltage Hysteresis" setting and balancing cycle continues until this is met.
- Fri Apr 12, 2024 11:54 am
- Forum: Battery Managment (BMS)
- Topic: BMW 330e pack balancing
- Replies: 13
- Views: 829
Re: BMW 330e pack balancing
Cells in series per string should be 96.
- Fri Apr 12, 2024 10:08 am
- Forum: Battery Managment (BMS)
- Topic: BMW 330e pack balancing
- Replies: 13
- Views: 829
Re: BMW 330e pack balancing
balstat indicates which individual cells are being balanced. 1 balancing, 0 not balancing. It's one digit per cell so 0xFFFF is all 16 cells in a module balancing.
- Fri Apr 12, 2024 9:01 am
- Forum: Battery Managment (BMS)
- Topic: BMW 330e pack balancing
- Replies: 13
- Views: 829
Re: BMW 330e pack balancing
Simpbms code balances BMW phev packs. The rate is very slow, maybe only 2mV per hour so a 150mV imbalance could take 2 - 3 days to balance.
- Mon Apr 08, 2024 12:08 pm
- Forum: Projects
- Topic: [DRIVING] BMW Z3
- Replies: 348
- Views: 221932
Re: [WIP] BMW Z3
I think the numbers across the bottom are sample number. The time varies with "Burst length" but from tests I have done it is about 27-28ms per sample with "Burst length" = 10.
- Mon Apr 01, 2024 12:55 pm
- Forum: General
- Topic: Help with this ElectroHydraulic Power steering pump?
- Replies: 5
- Views: 366
Re: Help with this ElectroHydraulic Power steering pump?
It also looks similar to the Ford Galaxy pump BG91-3K514-AC.
I found some info for a Ford pump here. https://www.diyelectriccar.com/threads/ ... ump.88303/
I found some info for a Ford pump here. https://www.diyelectriccar.com/threads/ ... ump.88303/
- Thu Mar 28, 2024 11:09 pm
- Forum: Toyota/Lexus
- Topic: Gen 3 Prius Transaxle P410 Makes Clunky Noise.
- Replies: 26
- Views: 1772
Re: Gen 3 Prius Transaxle P410 Makes Clunky Noise.
Did today's testing unequivocally show that the inverter temperature is signed 8 bit?
If so then the GS450 tmphs/temp_inv_water still needs fixing
temp_inv_water=int8_t(mth_data[42]);
If so then the GS450 tmphs/temp_inv_water still needs fixing
temp_inv_water=int8_t(mth_data[42]);