Search found 41 matches
- Fri Jul 14, 2023 7:00 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
If you take a look at the Software Update section of the Zombieverter wiki page https://openinverter.org/wiki/ZombieVerter_VCU you'll see a photo of the connections. The red wire is tapping into a 3.3V line to power on the VCU. The other three wires are labelled on the VCU and the ST-Link (clk, dio...
- Sat Jul 08, 2023 7:30 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
Thanks so much for your post - you have given me hope
1. Can you please send me pics of how you connect to the serial not using wifi
2. I need to know which plugs or converters to use from a laptop to the board
3. What program do you use to update?
1. Can you please send me pics of how you connect to the serial not using wifi
2. I need to know which plugs or converters to use from a laptop to the board
3. What program do you use to update?
- Sat Jul 08, 2023 12:34 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
i didn't manage to do that as yet and test it out. will do so and update you guys. the auto refresh does not give the spot values Question : I managed to get the board working again via the wifi. I now left it connected to the battery as it loses it's toggle category visibility if i disconnect. Is i...
- Fri Jun 23, 2023 9:24 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
There is no need to reset the board to upload but I find occasionly the wifi module needs resetting after. This is easy if working on the bench with the Wemos module as it has a reset button, otherwise power cycle the board. Are you using a board from Damien with the firmware pre-intstalled? I will...
- Fri Jun 23, 2023 9:20 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
Have you mapped your throttle yet? You can select the pot values to graph, and click start graph, watch the plot change as you move the throttle. Set pot min and pot max to fit the values in the range your Thorttle pedal provides, Also you must set up the type of throttle, single, single regen, dua...
- Thu Jun 22, 2023 6:51 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
do i have to reset the board to upload the software
as when i upload it goes though to 100%, says update done - however there is no change and still cannot see spot values
as when i upload it goes though to 100%, says update done - however there is no change and still cannot see spot values
- Wed Jun 21, 2023 7:09 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
I changed UDC to 0 volts and now opmode says run
however throttle 2 error comes up when i click refresh
however throttle 2 error comes up when i click refresh
- Wed Jun 21, 2023 6:56 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
Hi Everyone Great news - i tried uploading software onto zombieboard many many times and it did not want to work. On Sunday i was showing someone how it didn't work and it did. So now i got the spot values. Next problem- when i do the op mode by switching T15 on and HV request on (Time code 01:11:56...
- Mon Apr 03, 2023 6:54 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
Sorry Adrian i forgot to reply to you - yes we using the Wemos one
- Mon Apr 03, 2023 6:53 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
Update - the activity led is not flashing at all
Thanks guys - will attempt to get a usb serial adaptor and try to work out how to do it
Will also try to isolate inverter and shunt and see what happens
Thanks again
Thanks guys - will attempt to get a usb serial adaptor and try to work out how to do it
Will also try to isolate inverter and shunt and see what happens
Thanks again
- Mon Apr 03, 2023 9:53 am
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
we uploaded via UART
both ISA shunt and inverter were on CAN 2.
Is this correct?
both ISA shunt and inverter were on CAN 2.
Is this correct?
- Sun Apr 02, 2023 1:50 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
1. We uploaded the stm32_vcu. bin file 2. It says upload complete but never has any percentage no matter how long we wait. 3. We are receiving burst of data from laptop to out of wifi module 4. No signal returned from CPU 5. Have checked all supply voltages are present (12v, 5v and 3,3volts) 6. Powe...
- Sat Apr 01, 2023 8:02 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Re: Zombieverter no spot values showing
Yes you are right - i used SWD.
However i did use the UART update function. I downloaded the stmvcu_32.bin file.
When i uploaded the file - it said update completed.
It's still not showing spot values.
However i did use the UART update function. I downloaded the stmvcu_32.bin file.
When i uploaded the file - it said update completed.
It's still not showing spot values.
- Sat Apr 01, 2023 12:48 pm
- Forum: Vehicle Control (VCU)
- Topic: Zombieverter no spot values showing
- Replies: 26
- Views: 9044
Zombieverter no spot values showing
Hi I initially was getting the spot values. We were getting some strange voltage values from our shunt We realised we connected shunt to 5volt supply. We then changed the supply to 12volts. When we switched everything on again we got no spot values. I tried reloading the sim32_vcu.bin. Its reads SWD...
- Mon Feb 20, 2023 5:20 am
- Forum: Inverters / Motor Controllers
- Topic: Outlander front inverter
- Replies: 1
- Views: 469
Outlander front inverter
Hi guys
Can someone please help me with the wiring for the inverter to connect to the ZombieVerter.
I need the 12 volts, ground, can high and can low wire colours.
Please see screenshot of Damien video however i cannot make out the wiring.
Thanks
Can someone please help me with the wiring for the inverter to connect to the ZombieVerter.
I need the 12 volts, ground, can high and can low wire colours.
Please see screenshot of Damien video however i cannot make out the wiring.
Thanks
- Mon Feb 13, 2023 3:12 pm
- Forum: Mitsubishi
- Topic: Mitsubishi Outlander Front inverter
- Replies: 7
- Views: 4212
Mitsubishi Outlander Front inverter
Hi guys
I am using the front generator motor with the front inverter for our ev setup.
Can someone please tell me what the connections on the attached pic are.
I need to know where the dv voltage goes and which 3 terminals to connect to the motor.
Thanks
I am using the front generator motor with the front inverter for our ev setup.
Can someone please tell me what the connections on the attached pic are.
I need to know where the dv voltage goes and which 3 terminals to connect to the motor.
Thanks
- Sat Feb 04, 2023 3:34 pm
- Forum: Mitsubishi
- Topic: Mitsubishi Outlander accelerator pedal
- Replies: 1
- Views: 3322
Mitsubishi Outlander accelerator pedal
Hi Everyone
Does anyone know what the 6 wires on the Mitsubishi Outlander accelerator pedal do?
I need to connect to ZombieVerter.
Thanks
Does anyone know what the 6 wires on the Mitsubishi Outlander accelerator pedal do?
I need to connect to ZombieVerter.
Thanks
- Sat Feb 04, 2023 1:31 pm
- Forum: General
- Topic: Precharge and HV circuit
- Replies: 3
- Views: 459
Precharge and HV circuit
Hi guys
I have the gigavac gv242mab contractors and resistors.
What do the red, black, white and blue wires do?
Does anyone have a precharge and HV circuit we can follow?
Thanks
I have the gigavac gv242mab contractors and resistors.
What do the red, black, white and blue wires do?
Does anyone have a precharge and HV circuit we can follow?
Thanks
- Wed Jan 04, 2023 2:11 pm
- Forum: Classifieds
- Topic: Wanted: Mitsubishi Outlander charger
- Replies: 0
- Views: 368
Wanted: Mitsubishi Outlander charger
Hello Everyone
Blessed New Year to you all.
Has anyone got a Mitsubishi Outlander charger for sale?
Thanks
james
Blessed New Year to you all.
Has anyone got a Mitsubishi Outlander charger for sale?
Thanks
james
- Thu Dec 22, 2022 9:58 pm
- Forum: Classifieds
- Topic: Gigavac gv242mah
- Replies: 0
- Views: 343
Gigavac gv242mah
Hi All
I am looking for
1. IVT-1K-U3-I-CAN2-12
2. Gigavac GV242MAB contactor with built in economisers
3. Panasonic AEV52012 Relay
Thanks
james
I am looking for
1. IVT-1K-U3-I-CAN2-12
2. Gigavac GV242MAB contactor with built in economisers
3. Panasonic AEV52012 Relay
Thanks
james
- Wed Dec 21, 2022 11:36 pm
- Forum: Classifieds
- Topic: Parts needed
- Replies: 1
- Views: 346
Parts needed
Hello Everyone
I am looking for ff
1. IVT-1K-U3-I-CAN2-12
2. Gigavac GV242MAB contactor with built in economisers
3. Panasonic AEV52012 Relay
Thanks
james
I am looking for ff
1. IVT-1K-U3-I-CAN2-12
2. Gigavac GV242MAB contactor with built in economisers
3. Panasonic AEV52012 Relay
Thanks
james
- Thu Dec 15, 2022 11:49 pm
- Forum: Classifieds
- Topic: BMW i3 22kWh pack available
- Replies: 4
- Views: 1371
Re: BMW i3 22kWh pack available
Hi PaulSciroccoEV wrote: ↑Wed May 05, 2021 6:42 pm Yes, still available. I've got 8 Tesla Model S modules too.
I presume you have sold the BMW battery pack. If you haven't i might be interested. Currently trying to find out how to ship to South Africa and the fees to ship. Thanks james
- Thu Dec 15, 2022 8:58 pm
- Forum: Classifieds
- Topic: Wanted - BMW S-Box
- Replies: 3
- Views: 564
- Thu Dec 15, 2022 8:21 pm
- Forum: Mitsubishi
- Topic: Mitsubishi Outlander generator motor and inverter
- Replies: 11
- Views: 4753
Re: Mitsubishi Outlander generator motor and inverter
Sounds like a good idea. How heavy is it? i bought the generator and inverter in the UK and brought it back with me to South Africa. Hoping it's not too heavy to fit in my luggage - we planning on coming to visit outlaws in UK around November Hi We arrived in UK about 3 weeks or so ago. I am not go...
- Mon Aug 08, 2022 6:53 pm
- Forum: Mitsubishi
- Topic: Mitsubishi Outlander generator motor and inverter
- Replies: 11
- Views: 4753
Re: Mitsubishi Outlander generator motor and inverter
I am getting a bit confused. Is zombieverter and arduino two different things? I thought that i have to buy a zombieverter and arduino is the program that controls it. And i don't know one thing about arduino.