this is great, exactly what I was looking for, thank you for the write up, I see there's a couple of them listed on eBay for under $150, I may get one for funsies

Working with High Voltage Safety Tips

I had an alternative solution. If that's true, it's surely so stupid that many people have complained about it before... https://priuschat.com/threads/accelerator-pedal.77114/ "The pedal itself apparently has no internal stop but relies on the pedal travel bottoming into the floor carpet. The ...

so here's Big Blue, a 2011 Toyota Prius that gave her life so that we could have this pedal, and I have gotten these pedals ranging from for FREE, to $5 dollars on their 50% OFF Sale Days, to whatever they felt like charging me on that day IMG_0931.JPG IMG_0933.JPG I think it is worth sharing how it...

84 VW MK1 Rabbit DIY Wire Harness Fuse Block & BMW Safety Box Part 1





What is he up to now?

A hunch... When autorefresh is on, the search bar refreshes faster than you can get to the 2nd search item. I've come across a few things like that, that seemed like they were broken or unresponsive, and it was just the auto-refresh. ... On variable names, I'm onboard with you. They're programmer-f...

I was going to use the start position of my ignition switch to enable drive, but in my car the Ign pos 1 and 2 are disconnected from the battery when I do. Probably to ensure the starter gets 100% of battery power but I was disappointed when I discovered this as it caused issues else where. It's no...

ZombieVerter VCU Wont RUN

first up was the 3rd Gen Prius 2011 pedal


those of you following the VW Rabbit conversion may recall we had to trim this Prius pedal to keep it from bottoming out

Alibro wrote: ↑Wed May 01, 2024 4:44 pm From the photo they look like little sperm swimming around looking for an egg.

how did I miss this epic comment ???

I presume you know this, but the reason the pins on a switch are counterintuitive, is because the switch has a pivot in the middle. Like a teeter totter, when one side of the lever goes up, the other side goes down. So the back end of the lever that actually does the switching, points to the opposi...

84 VW MK1 Rabbit DIY Wire Harness Forward & Reverse Switch https://youtu.be/GGYUhMiJOkw these are the two pins needed for the Forward and Reverse Switch, but there are many ways to skin this cat IMG_4287 Labeled.jpg the switch is hugging the fuse block just for the photo opp, that's not where i...

Jacobsmess wrote: ↑Wed May 01, 2024 5:14 pm Solution: 6 pedal driving.

message received !

decisions, decisions...


Center Stage: The G.O.A.T. aka Pedalus Maximalus BMW E46 Part# 3542 6762481-03 the pedal that started it all !
(please show sum respect)

Alibro wrote: ↑Wed May 01, 2024 6:51 am One pedal driving?

ha ha, right!?

MattsAwesomeStuff wrote: ↑Wed May 01, 2024 9:15 am "You might see stuff like that, where your pin was underneath the pin and looked like it was on but wasn't"

...

OMG, as my old boss would say, at least he's consistent !

out with the old...

How to do a ZombieVerter VCU Ver 2.15 A Firmware Upgrade

we find the dirmode [direction mode] under the Parameters aka "Settings" section in the Open Inverter web interface for the ZombieVerter VCU accessible via WiFi DefaultForward is our fifth choice. This setting tells the VCU that as soon as we turn the key to the Run position we are ready t...

we find the dirmode [direction mode] under the Parameters aka "Settings" section in the Open Inverter web interface for the ZombieVerter VCU accessible via WiFi SwitchReversed is our fourth choice. You would use this if say you took a rear motor from an OEM vehicle and flipped it to instal...

we find the dirmode [direction mode] under the Parameters aka "Settings" section in the Open Inverter web interface for the ZombieVerter VCU accessible via WiFi ButtonReversed is our third choice. You would use this if say you took a rear motor from an OEM vehicle and flipped it to install...

used for depinning this type of harness from AliExpress


the orange thing appears to be just a shield to either prevent the tool from getting damaged or you from getting cut, maybe

not sure where this belongs so dropping it here, hope it helps somebody out

REMOVAL TOOL FOR FEMALE TERMINALS
Manufacturer: Aptiv (formerly Delphi)
TTI Part Number: 210S048
Mfr Part Number: 210S048
Price: $65

we find the dirmode [direction mode] under the Parameters aka "Settings" section in the Open Inverter web interface for the ZombieVerter VCU accessible via WiFi

Switch is our second choice.

just want to share some screen shots with those who are still waiting on their Zombies to arrive ;) we find the dirmode [direction mode] under the Parameters aka "Settings" section in the Open Inverter web interface for the ZombieVerter VCU accessible via WiFi Button is our first choice. T...