i have checked all connections !

Do any of you have GEN1 working on the Zonmbie?

Just for your information:
I also had problems at the beginning that the PC can connect to the Zombie !

After that I used a USB - Wifi and now the connection works!

Digitus DN-7042-1 WLAN Stick USB 2.0 150 MBit/s

thanks for the tip

I have already seen the video

do you have a solution?

https://www.youtube.com/watch?v=vHrb0n2qNzM these are my parameters I cannot find an error do you have the solution danke peter parameter value Vehicle Module Inverter Leaf_Gen1 Vehicle None Throttle potmin 156 dig potmax 840 dig pot2min 305 dig pot2max 2042 dig regentravel 30 % regenmax -30 % potmo...

Hello,

I am very glad that the motor turns !!!

forwards everything is OK
only in reverse the engine turns to a constant speed and stays there until I switch to forward again

what could be the problem ?

Hello,

I am very glad that the motor turns !!!

forwards everything is OK
only in reverse the engine turns to a constant speed and stays there until I switch to forward again

what could be the problem ?

thanks for the video !

It has shown me many interesting things !

Hi Dämon
I have the same problem and can't get CAN signals to CAN2.


Hi Paul
I can take photos tomorrow of how I soldered the loose components onto the board.

then we can try to compare

thank you for the support !!

only short question

should on CAN2 from the VCU signals come only with 12V applied ?

So that I can control my CAN connection and be sure that the VCU is working properly!
Now there are no CAN signals!

Thank you unfortunately I don't have an Arduino Due only Nano Have I understood this correctly? This is a code that I run via an Arduino which then sets the correct parameters in the Shant ? I will try it One more question If I apply voltage to the Zombie board, should CAN signals arrive at CAN2? I ...

Thanks for the answer ! Where can I find the code ? ( code in the zombieverter project (ISA::initialize) ) unfortunately I have a problem with the shunt ! It is strangely set to 1000kbps ( should be 500 ) I then tried to set it to 500kbps according to the instructions. now I cannot receive any data ...

Hello I need your help again I have ordered the shunt and connected it unfortunately I don't get any correct data displayed in the web interface for example udc 16777.18 udc2 -33554.4 udc3 -64225.25 idc -50311.62 If I connect an Arduino CAN shield with this code https://openinverter.org/wiki/Getting...

Thank you this has helped me a lot !!!

Please link it on the wiki page !!!


Thanks
Peter

hello, I hope you can help me! The first question : what does the red flashing LED on the zombieverter board mean ? I have a red one on the ESP and a red one on the board that are permanently lit and one on the board that is flashing. 2. i don't get any CAN data from the board What settings do I nee...

thank you for your message

hello
I have a simple question
how do the components that come loose in the kit are positioned?

they are not the same parts as in the video

there is no marking on the parts

does anyone have photos of the board



or a link where it is described

thanks
peter

Thank you for your professional answer ! If I connect the BMS and the charger with CAN, the system will work without the VCU? as in this diagram : https://activeautomation.co.nz/images/thumbs/0000631_blogimages.jpeg I have another question: I wanted to try powering the charger with 12V to read the C...

Hi
I think this is better if it is here

it is about the zombieverter

please for a technical information

Thanks
Peter

Hello conversion friends, I am Peter from Germany and a beginner in converting vehicles ! I will install a Leaf Gen1 in a Mercedes W123. Both cars I already have and the Leaf components I have already removed I have already ordered the ZombieVerter I have a request to the specialists Which of the Le...