ZombieVerter IO - Revision history

Rstevens81: /* Pin functions:[edit | edit source] */

2025-07-27T14:20:23Z

Pin functions:[edit | edit source]

← Older revision		Revision as of 14:20, 27 July 2025
Line 54:		Line 54:
	* CpSpoof - PWM OUTPUT: used to spoof CP signal to OBC if also using a charging interface such as FOCCCI or I3LIM		* CpSpoof - PWM OUTPUT: used to spoof CP signal to OBC if also using a charging interface such as FOCCCI or I3LIM
	* GS450Hpump - PWM OUTPUT: used to run GS450H oil pump		* GS450Hpump - PWM OUTPUT: used to run GS450H oil pump
	* Switch_NoRegen - DIGITAL INPUT - when active throttle regen and brake regen are inhibited, this allows much easier up/down shifting if the motor is connected to a manual transmission (NOT currently in released firmware 2.22A, however will be in next release)		* Switch_NoRegen - DIGITAL INPUT - when active throttle regen and brake regen are inhibited, this allows much easier up/down shifting if the motor is connected to a manual transmission (NOT currently in released firmware 2.22A, however will be in next release) ... Note this is a hard on/off so can be quite noticeable in low gear

	==== Proximity Pilot[edit \| edit source] ====		==== Proximity Pilot[edit \| edit source] ====

Rstevens81: /* Pin functions:[edit | edit source] */

2025-07-27T13:51:09Z

Pin functions:[edit | edit source]

← Older revision		Revision as of 13:51, 27 July 2025
Line 54:		Line 54:
	* CpSpoof - PWM OUTPUT: used to spoof CP signal to OBC if also using a charging interface such as FOCCCI or I3LIM		* CpSpoof - PWM OUTPUT: used to spoof CP signal to OBC if also using a charging interface such as FOCCCI or I3LIM
	* GS450Hpump - PWM OUTPUT: used to run GS450H oil pump		* GS450Hpump - PWM OUTPUT: used to run GS450H oil pump
			* Switch_NoRegen - DIGITAL INPUT - when active throttle regen and brake regen are inhibited, this allows much easier up/down shifting if the motor is connected to a manual transmission (NOT currently in released firmware 2.22A, however will be in next release)

	==== Proximity Pilot[edit \| edit source] ====		==== Proximity Pilot[edit \| edit source] ====

LRBen: /* Pin functions:[edit | edit source] */

2025-02-16T21:13:03Z

Pin functions:[edit | edit source]

← Older revision		Revision as of 21:13, 16 February 2025
Line 45:		Line 45:
	* ReverseLight - OUTPUT: activates when direction is reverse		* ReverseLight - OUTPUT: activates when direction is reverse
	* BrakeVacPump DIGITAL OUTPUT: when BrakeVacSensor below threshold this is turned on.		* BrakeVacPump DIGITAL OUTPUT: when BrakeVacSensor below threshold this is turned on.
	* HeatReq - DIGITAL INPUT: ~~12v signal input, when you want the VCU to start the heater.~~		* HeatReq - DIGITAL INPUT:
	* HVRequest - DIGITAL INPUT - when used with ext charger setting will start precharge cycle and put VCU into charge mode.		* HVRequest - DIGITAL INPUT - when used with ext charger setting will start precharge cycle and put VCU into charge mode.
	* ProxPilot - ANALOGUE INPUT - detect a charging cable plug in, requires external resistors, values depend on type 1 or type 2		* ProxPilot - ANALOGUE INPUT - detect a charging cable plug in, requires external resistors, values depend on type 1 or type 2

LRBen: /* Pin functions:[edit | edit source] */

2025-02-16T21:10:44Z

Pin functions:[edit | edit source]

← Older revision		Revision as of 21:10, 16 February 2025
Line 45:		Line 45:
	* ReverseLight - OUTPUT: activates when direction is reverse		* ReverseLight - OUTPUT: activates when direction is reverse
	* BrakeVacPump DIGITAL OUTPUT: when BrakeVacSensor below threshold this is turned on.		* BrakeVacPump DIGITAL OUTPUT: when BrakeVacSensor below threshold this is turned on.
	* HeatReq - DIGITAL INPUT		* HeatReq - DIGITAL INPUT: 12v signal input, when you want the VCU to start the heater.
	* HVRequest - DIGITAL INPUT - when used with ext charger setting will start precharge cycle and put VCU into charge mode.		* HVRequest - DIGITAL INPUT - when used with ext charger setting will start precharge cycle and put VCU into charge mode.
	* ProxPilot - ANALOGUE INPUT - detect a charging cable plug in, requires external resistors, values depend on type 1 or type 2		* ProxPilot - ANALOGUE INPUT - detect a charging cable plug in, requires external resistors, values depend on type 1 or type 2

Tom91 at 20:03, 30 December 2024

2024-12-30T20:03:36Z

← Older revision		Revision as of 20:03, 30 December 2024
Line 1:		Line 1:
	~~[[Images/7/75/ZombieVerter VCU V1 cable side pinout2.jpg]]~~

	== Pin Input/Output and functions ==		== Pin Input/Output and functions ==
Line 6:		Line 5:
	Low side Outputs.		Low side Outputs.

	* GP Out 3		* Out1Func/GP Out 1
	* GP Out 2		* Out2Func/GP Out 2
	* GP Out 1		* Out3Func/GP Out 3
	* Trans SL1- (If not using the GS450H)		* Trans SL1- (If not using the GS450H)
	* ~~TransSL2~~- (If not using the GS450H)		* Trans SL2- (If not using the GS450H)

	Low side output connect to ground when activated. The low side outputs in Zombie are ideal for switching relays, such as for coolant pumps.		Low side output connect to ground when activated. The low side outputs in Zombie are ideal for switching relays, such as for coolant pumps.

Tom91 at 19:59, 30 December 2024

2024-12-30T19:59:43Z

← Older revision		Revision as of 19:59, 30 December 2024
Line 1:		Line 1:
	== Pin Input/Output and functions~~[edit \| edit source]~~ ==		[[Images/7/75/ZombieVerter VCU V1 cable side pinout2.jpg]]

			== Pin Input/Output and functions ==
	Zombieverter has a number of selectable input/output pins that can be used for a number of functions. These pins are:		Zombieverter has a number of selectable input/output pins that can be used for a number of functions. These pins are:

Line 6:		Line 8:
	* GP Out 3		* GP Out 3
	* GP Out 2		* GP Out 2
	* ~~Neg Contactor switch/~~GP Out 1		* GP Out 1
	* Trans SL1- (If not using the GS450H)		* Trans SL1- (If not using the GS450H)
	* TransSL2- (If not using the GS450H)		* TransSL2- (If not using the GS450H)
Line 64:		Line 66:

	List and Overview of [[Zombieverter Parameters and Spot Values]]		List and Overview of [[Zombieverter Parameters and Spot Values]]
			[[Category:ZombieVerter]]

Tom91: Created page with "== Pin Input/Output and functions[edit | edit source] == Zombieverter has a number of selectable input/output pins that can be used for a number of functions. These pins are: Low side Outputs. * GP Out 3 * GP Out 2 * Neg Contactor switch/GP Out 1 * Trans SL1- (If not using the GS450H) * TransSL2- (If not using the GS450H) Low side output connect to ground when activated. The low side outputs in Zombie are ideal for switching relays, such as for coolant pumps. High si..."

2024-12-30T19:56:52Z

Created page with "== Pin Input/Output and functions[edit | edit source] == Zombieverter has a number of selectable input/output pins that can be used for a number of functions. These pins are: Low side Outputs. * GP Out 3 * GP Out 2 * Neg Contactor switch/GP Out 1 * Trans SL1- (If not using the GS450H) * TransSL2- (If not using the GS450H) Low side output connect to ground when activated. The low side outputs in Zombie are ideal for switching relays, such as for coolant pumps. High si..."

New page

== Pin Input/Output and functions[edit | edit source] ==
Zombieverter has a number of selectable input/output pins that can be used for a number of functions. These pins are:

Low side Outputs.

* GP Out 3
* GP Out 2
* Neg Contactor switch/GP Out 1
* Trans SL1- (If not using the GS450H)
* TransSL2- (If not using the GS450H)

Low side output connect to ground when activated. The low side outputs in Zombie are ideal for switching relays, such as for coolant pumps.

High side PWM.

* PWM 3
* PWM 2
* PWM 1
* Pump PWM - Limited to GS450 Oil pump pwm or tacho pwm output

These are high side 12v outputs, usually for controlling gauges or auxiliary items than need a pwm signals. They are not suitable for controlling relays.

Ground Input pins

These pins pull down to ground only. '''Do not connect any voltage to these pins.'''

PB1

PB2

PB3

====== Pin functions:[edit | edit source] ======
''Note: While the web interface will allow input pins to be set to output and vice versa this will not actually work.''

* ChaDemoAIw - OUTPUT - used as part of the Chademo charging protocol for the charge allow output to the charger.
* OBCEnable - OUTPUT: activates as part of the ExtCharger module
* HeaterEnable - OUTPUT: activates only in run mode and when coolant pump is on
* RunIndication - OUTPUT: activates when zombie is in run mode
* WarnIndication - OUTPUT
* CoolantPump - OUTPUT: activates during precharge, usually used for coolant pumps
* NegContactor - OUTPUT: activates during precharge for negative contactor
* BrakeLight - OUTPUT: activates when brake input is detected
* ReverseLight - OUTPUT: activates when direction is reverse
* BrakeVacPump DIGITAL OUTPUT: when BrakeVacSensor below threshold this is turned on.
* HeatReq - DIGITAL INPUT
* HVRequest - DIGITAL INPUT - when used with ext charger setting will start precharge cycle and put VCU into charge mode.
* ProxPilot - ANALOGUE INPUT - detect a charging cable plug in, requires external resistors, values depend on type 1 or type 2
* BrakeVacSensor - ANALOGUE INPUT - read a vacuum sensor and turn on the BrakeVacPump DIGITAL OUTPUT
* CoolingFan - OUTPUT: activates when FanTemp setpoint is reached
* HVActive - OUTPUT: activates when contactors are closed and VCU is in run or charge mode
* PWMTim3 -
* CpSpoof - PWM OUTPUT: used to spoof CP signal to OBC if also using a charging interface such as FOCCCI or I3LIM
* GS450Hpump - PWM OUTPUT: used to run GS450H oil pump

==== Proximity Pilot[edit | edit source] ====
This analogue input used to detect a charging cable is plugged in.

A resistor to the 5v needs to be connected to the analogue in pin, 330 ohms in the spec, and R5 needs to be another resistor between analogue in pin and ground. Type 1 connectors should be a 2.7k ohm resistor and type 2 should be 4.7k ohm. Note the charging port may already have this resistor installed.

Open up the Zombie UI and choose ProxPilot for the function of the analogue in pin. Then start plotting PPVal and then plug in, you can then use this to select your PPThreshold. Bare in mind the resistance will vary on the cable plugged in depending on the Amps it can supply.

<nowiki>https://www.youtube.com/watch?v=U3c4V8vMb6k</nowiki> Video here for the setup and demonstration.

List and Overview of [[Zombieverter Parameters and Spot Values]]