Tesla Parameters Thread

Topics concerning the Tesla front and rear drive unit drop-in board
Golf_mkIII_E
Posts: 32
Joined: Tue Apr 20, 2021 8:55 pm

Re: Tesla Parameters Thread

Post by Golf_mkIII_E »

No, I’m going to sell the components. I don’t have as much spare time anymore anytime soon.
User avatar
EV_Builder
Posts: 1199
Joined: Tue Apr 28, 2020 3:50 pm
Location: The Netherlands
Has thanked: 16 times
Been thanked: 33 times
Contact:

Re: Tesla Parameters Thread

Post by EV_Builder »

How scarce are those golfs? Can't you convert another one?
Would be quite easy since allot fits?

P.s. if I think what you are telling without telling it: congratulations 🙂
Converting an Porsche Panamera
see http://www.wdrautomatisering.nl for bespoke BMS modules.
tom91
Posts: 1271
Joined: Fri Mar 01, 2019 9:15 pm
Location: Bristol
Has thanked: 97 times
Been thanked: 201 times

Re: Tesla Parameters Thread

Post by tom91 »

Golf_mkIII_E wrote: Fri Mar 04, 2022 4:46 pm I’m currently testing some setups with very high Fweak and Fslipmax. I’m able to pull 1150A consistently now from about 95kmh to about 155kmh. Acceleration is really impressive.
Mind sharing the settings if you have them saved? Which version is it on?

Anyone have a good known beginning set for the latest firmware version?
Founder Volt Influx https://www.voltinflux.com/
jon volk
Posts: 572
Joined: Wed Apr 10, 2019 7:47 pm
Location: Connecticut
Been thanked: 2 times

Re: Tesla Parameters Thread

Post by jon volk »

I did a full dump of my current LDU parameters for normal driving and modified anything that I’m doing over CAN to be a reasonable starting static value.
Attachments
TESLA_PARAMS.json
(1.47 KiB) Downloaded 118 times
Formerly 92 E30 BMW Cabrio with Tesla power
ViktorT
Posts: 25
Joined: Wed Aug 21, 2019 1:39 pm
Location: South Sweden

Re: Tesla Parameters Thread

Post by ViktorT »

Hi
I have a SDU fitted into an alfa 147. I wonder about the brake signal that goes into pin 10. Is it enough to have the brake light switch from pin 15 to steer the regen?
Alfa Romeo 147 with Tesla FDU and Kia soul pack
User avatar
johu
Site Admin
Posts: 5681
Joined: Thu Nov 08, 2018 10:52 pm
Location: Kassel/Germany
Has thanked: 153 times
Been thanked: 959 times
Contact:

Re: Tesla Parameters Thread

Post by johu »

You can do that, control will just be very basic regen on/off. In addition you can configure off pedal regen that is proportional to how much you come off the throttle
Support R/D and forum on Patreon: https://patreon.com/openinverter - Subscribe on odysee: https://odysee.com/@openinverter:9
ViktorT
Posts: 25
Joined: Wed Aug 21, 2019 1:39 pm
Location: South Sweden

Re: Tesla Parameters Thread

Post by ViktorT »

Thanks Johannes,
Another question; Im having the SDU in opposite direction. Is there any way to change the fwd/reverse direction in the parameters or does it matter? Im thinking about the cruise, does it work in rev direction? And the CAN signal, does it give negative speed when going in reverse?
Alfa Romeo 147 with Tesla FDU and Kia soul pack
User avatar
johu
Site Admin
Posts: 5681
Joined: Thu Nov 08, 2018 10:52 pm
Location: Kassel/Germany
Has thanked: 153 times
Been thanked: 959 times
Contact:

Re: Tesla Parameters Thread

Post by johu »

You can swap the meaning of forward and reverse inputs
Cruise works both directions
Speed is always positive
Support R/D and forum on Patreon: https://patreon.com/openinverter - Subscribe on odysee: https://odysee.com/@openinverter:9
ViktorT
Posts: 25
Joined: Wed Aug 21, 2019 1:39 pm
Location: South Sweden

Re: Tesla Parameters Thread

Post by ViktorT »

I bought a gaming joystick to use as a selector. But most project I seen have a knob. Does the signal input for fwd, backwrd need to be constant or can they be of pulse type?
Alfa Romeo 147 with Tesla FDU and Kia soul pack
User avatar
Romale
Posts: 441
Joined: Fri May 20, 2022 4:16 pm
Location: Romania
Has thanked: 204 times
Been thanked: 45 times

Re: Tesla Parameters Thread

Post by Romale »

ViktorT wrote: Thu Jul 21, 2022 6:45 am I bought a gaming joystick to use as a selector. But most project I seen have a knob. Does the signal input for fwd, backwrd need to be constant or can they be of pulse type?
in the settings there is an option to use a constant signal or pulse. so maybe you can use it.
evil neodymium :twisted:
Post Reply