GAZ-24 Volga 1983г.

Tell us about the project you do with the open inverter
Post Reply
Vijaya
Posts: 7
Joined: Sat Jun 05, 2021 7:28 pm

GAZ-24 Volga 1983г.

Post by Vijaya »

Hello dear friends.My name is Vadim,I'm from Russia.Please give me some advice where to buy me the simplest electricity and a motor to make it go? I don't understand anything yet. My compliments to yo
Vijaya
Posts: 7
Joined: Sat Jun 05, 2021 7:28 pm

Re: GAZ-24 Volga 1983г.

Post by Vijaya »

:)
Vijaya wrote: Mon Jun 07, 2021 10:13 am Hello dear friends.My name is Vadim,I'm from Russia.Please give me some advice where to buy me the simplest electricity and a motor to make it go? I don't understand anything yet. My compliments to yo
Vijaya
Posts: 7
Joined: Sat Jun 05, 2021 7:28 pm

Re: GAZ-24 Volga 1983г.

Post by Vijaya »

NksMXdWIWWw.jpg
User avatar
johu
Site Admin
Posts: 5769
Joined: Thu Nov 08, 2018 10:52 pm
Location: Kassel/Germany
Has thanked: 157 times
Been thanked: 1011 times
Contact:

Re: GAZ-24 Volga 1983г.

Post by johu »

Welcome, sexy photo :D
Cheapest option is probably Toyota Prius Gen2 inverter & transaxle plus a hybrid battery. We have some Russian speakers here who are using this.
Support R/D and forum on Patreon: https://patreon.com/openinverter - Subscribe on odysee: https://odysee.com/@openinverter:9
Vijaya
Posts: 7
Joined: Sat Jun 05, 2021 7:28 pm

Re: GAZ-24 Volga 1983г.

Post by Vijaya »

Thank you dear friend.Please introduce me to Russian speakers and I will send you super sex photos and videos.
User avatar
jnsaff
Posts: 176
Joined: Fri Oct 18, 2019 7:42 am
Location: Tallinn, Estonia
Has thanked: 2 times
Been thanked: 8 times

Re: GAZ-24 Volga 1983г.

Post by jnsaff »

The Volga is RWD so maybe easier with the GS450h gear? You could probably also make it the fastest (and scariest) Volga in the world, for about 3 minutes until the diff or driveshaft or something else only meant to only handle about 100hp breaks.
Vijaya
Posts: 7
Joined: Sat Jun 05, 2021 7:28 pm

Re: GAZ-24 Volga 1983г.

Post by Vijaya »

This is the best advice. The Volga is being built as the most terrible. Looking for a bridge from GS. Thank you very much.All Glory to you
Vijaya
Posts: 7
Joined: Sat Jun 05, 2021 7:28 pm

Re: GAZ-24 Volga 1983г.

Post by Vijaya »

gearbox from GS450h found.Now I'm looking for the driveshaft .But where do I get an electric motor and powerful batteries?
User avatar
zilion
Posts: 58
Joined: Tue Feb 02, 2021 7:50 am
Location: Poland

Re: GAZ-24 Volga 1983г.

Post by zilion »

"gearbox from GS450h" is the electric motor, but check if you have with oil pump -it's commonly removed.
If you have one -change bearings.
https://openinverter.org/wiki/Motors
I smell lithium in the air. It's not lithium, it's glycolium.
Vijaya
Posts: 7
Joined: Sat Jun 05, 2021 7:28 pm

Re: GAZ-24 Volga 1983г.

Post by Vijaya »

Thank you, dear Zilian.I wanted to say that I found a differential on the rear wheel for good speed. Now I'm looking for a driveshaft combined with a good gearbox and a separate good engine.
User avatar
Jack Bauer
Posts: 3563
Joined: Wed Dec 12, 2018 5:24 pm
Location: Ireland
Has thanked: 1 time
Been thanked: 87 times
Contact:

Re: GAZ-24 Volga 1983г.

Post by Jack Bauer »

I'm going to need a hacksaw
User avatar
UStas
Posts: 35
Joined: Fri Nov 06, 2020 11:37 am
Location: Moscow (Russia)
Contact:

Re: GAZ-24 Volga 1983г.

Post by UStas »

Vijaya wrote: Mon Jun 07, 2021 10:13 am Hello dear friends.My name is Vadim,I'm from Russia.Please give me some advice where to buy me the simplest electricity and a motor to make it go? I don't understand anything yet. My compliments to yo
Let me switch to russian.

Вадим, есть ряд русскоязычных форумов по электротранспорту :
https://electroavtosam.com.ua/forums/
https://electrotransport.ru/ussr/index.php

Буду рад если заглянешь в мою тему про переоборудование Опель Тигра, ссылка ниже.

Сами запчасти по доступным ценам можно искать на сайте farpost.ru
Например двигатель Outlander MGR я купил там за 5000 руб - $72 !!!

Но чтобы оживить инвертор конечно нужны будут "мозги" от Демьена с этого сайта.
Вариантов много:
Можно купить готовую настроенную плату (дорого, но меньше всего хлопот),
Можно купить частично собранную плату и допаять все необходимое самому (средняя цена, но нужно иметь навыки пайки и прошивки MCU),
Можно воспользоваться документацией в свободном доступе и заказать изготовление плат в Китае (выгодно если делать несколько проектов).
Post Reply