I haven't got any experience with CAN FD. Though, communication works in general and I think the CAN matrix makes sense. I can read the motor RPM while rotating the shaft, read the correct HV that the MCU reports, and I also see the errors popping up when I remove the MCU-motor LV cabling. The only...

More and more i am convinced your motor uses CAN FD for communication instead of plain CAN bus. Try to see if you receive any reports on 0x105 telegram if you rotate the shaft with inverter started.

What is the repetition frequency for your telegrams? Normaly i would expect "drive" and "alive" telegrams to work at 100ms intervals and "BMS" telegram to work at 500ms or so. Do you have each byte declaration? I.E. byte0 value is start, byte1 and byte2 are voltage val...

What sort of size vacuum tanks for braking is generally being used for conversion ? Is this one OK ? https://www.ebay.co.uk/itm/225975793716 I found additional tank unneccary complication and too much plumbing. First try to connect pump directly but leave provision for tank if needed. Use of good s...

It would be safer to use a electronic load, I have used a Tenma 72-13210 120V 300W to discharge batteries to a known voltage, it took quite a while at only 300W though. I think you could use that JK BMS with output and connect cell points so it will operate power transistors. Then connect a load li...

I am considering purchasing these same motors(or similar, also from Magelec). The seller on Ebay who I would buy from says that he will send a user manual and a CAN msg-list. If I do so I'll share here, but I am concerned at the lack of resources reagrding this company. I haven't seen any informati...

Is it necessary to assemble a pre-charging circuit before the inverter? Or can I just connect the wires and plug the power supply plug into the outlet? Precharge wiring contains DC contactor + DC relay + precharge resistor. As any HV assembly you need to test it in operation before you can rely on ...

Surely, it is no secret to many that in an ATX computer power supply there is 320 volts of DC voltage running on a large filter capacitor after the diode bridge. It is known that the diode bridge is not very powerful - only 6 amps. Now the question. Is it safe to use such a power supply to spin the...

Hi, i am installing Tesla Gen2 charger to my Mazda and i need to setup a disable circuit for VCU so that someone cant just drive off with charge cable connected :). I am looking at schematic for both connectors and i notice there are two additional pins which are ready as input and output but dont s...

So as the LFP packs are starting to be used in OEM EVs more widely wonder what chances do we have to use those in projects and conversions? Mainly it is difficult to determine how much charge they have left. What would be our options for BMS and SOC estimation? Would hacking the OEM BMS be a necess...

Paint It Black And Put It Back ! IMG_3504.JPG That looks really good! Hm... did you accoount for the movement of the loaded axle? It should have like 0.5cm movement in its loaded position. Just saying because i didnt think of that the first time and i had to shave the CV side down on the lathe!!!

Hi, i am installing Tesla Gen2 charger to my Mazda and i need to setup a disable circuit for VCU so that someone cant just drive off with charge cable connected :). I am looking at schematic for both connectors and i notice there are two additional pins which are ready as input and output but dont s...

Could it be that in map 3 the ramping is not used, so you could be getting quite big jumps in torque requests? I resolved this by going through values in the array. I made some jumps in values where throttle would be held, but RPMs increased. This resulted in values jumping up and down and then set...

this is queued up to how I hope to make it straight(ish) https://www.youtube.com/watch?v=NkQc7eshiXI&t=532s Now that is informative! Really shows theory and pactical application. Must see if you are extending some shafts. I just luve the NDT penetrant inspection. Some of the mechanics are shyin...

..... Anvil's are stupid expensive where I live, how about in your hood? Let me tell you something... even me, i shy from replacing the whole panel at the rear seats like you just did. Kudos! I simply took OBCs as far up as they would go and designed mounts from the underside. But i do have an anvi...

Gregski wrote: ↑Wed Apr 03, 2024 5:28 pm bwhaaa haa ha, did I mention I had an assistant !

And expectation led me to belive i was going to see the actual use of that damn contraption together with a chapter of english wheel and tap hammer application . Well done.

My daughter asked me if i could mount a rear camera to Mazda. I thought what to use best and i decided to buy a radio with 3.2in LCD display. That display has a connection to plug in vide input from camera. Screenshot_20240320-115503_AliExpress.jpg I bought a small 8 LED camera and mounted it above ...

I am now trying to install 3phase Tesla Gen2 charger despite the fact that the last 12S battery module occupies its space under the rear seats now. I asked my friend to cut and weld me a flat mount where Tesla charger will fit behind the rear seats in the trunk area. I will use rear seat belt bolts ...

Thanks arber, that reply hits every single one of my questions! Perhaps a more obvious one. My canbus network is terminated by a Zombieverter on one end and an IVT shunt on the other (it has an internal resistor). Am I correct in assuming I can connect these chargers (plus my outlander heater and A...

Gregski wrote: ↑Mon Apr 01, 2024 2:43 pm VW MK1 Outlander Battery Charger Install DIY EV 2

Yes... i think your idea is doable.

Hello, ...... 1. I was wondering if anyone had instructions on how to wire them in 3 phase configuration? Observe this post and links to my site... https://openinverter.org/forum/viewtopic.php?p=63766#p63766 https://leafdriveblog.wordpress.com/2018/11/05/volvo-eltek-3kw-charger/ https://leafdrivebl...

Here you could observe how i managed to install Outlander OBCs. https://leafdriveblog.wordpress.com/2020/11/29/installing-outlander-charger/ https://openinverter.org/forum/download/file.php?id=6896&mode=view I used OEM mont points on the sd o the charger. I made several mounts and then pressed/a...

VW MK1 Outlander Battery Charger Install DIY EV Part I https://youtu.be/hdDECKioUz4 There is enough space to put 2x OBCs there... I tried to command two chargers by transmitting CP PWM signal... and it worked! You could get yourself two phase charging... or 6kW single phase if you connect them to y...

Gregski wrote: ↑Sat Mar 30, 2024 4:37 pm It's a Polack thang...

I dont think you can trademark like that!
Shall i mention our Janja ..?

Question 2: I have made a really good pedal map setup for me i think. The only thing i am bothered with is fast torque transition when i am already rolling, maybe between 250rpm and 500rpm. There is a weird shaking there but then it becomes smooth as i go through the rpm. What would that be? Are th...