Search found 783 matches

by Bratitude
Thu Mar 21, 2024 2:13 pm
Forum: Projects
Topic: [WIP] 1998 Nissan Frontier Minitruck - LEAF 40kwh
Replies: 22
Views: 2233

Re: [WIP] 1998 Nissan Frontier Minitruck - LEAF 40kwh

That tilt bed sure makes it look easier to work on!

Good to see the boxes just fit. I’ll be replicating the same with my 720.
by Bratitude
Mon Mar 18, 2024 1:05 am
Forum: Projects
Topic: [DRIVING] 1940 Chevrolet with Tesla Motor
Replies: 128
Views: 29876

Re: [DRIVING] 1940 Chevrolet with Tesla Motor

These old ldu seem to be fairly problematic! The power tho…
by Bratitude
Sun Mar 17, 2024 1:38 am
Forum: Projects
Topic: 1984 Voltswagen Rabbit Prius Gen 3 ZOMBIE
Replies: 280
Views: 16857

Re: 1984 Voltswagen Rabbit Prius Gen 3

One question I would have is how much in/out movement would VW shafts typically allow? I believe the cup type has quite a bit allowable travel, but I'm less familiar with how the VW joints deal with in/out travel. I'm sure you know much more about this given your current project. the plunge on the ...
by Bratitude
Fri Mar 15, 2024 11:06 pm
Forum: Projects
Topic: 1984 Voltswagen Rabbit Prius Gen 3 ZOMBIE
Replies: 280
Views: 16857

Re: 1984 Voltswagen Rabbit Prius Gen 3

It seems against all odds that this would be within the same range. why? diffs are diffs, they are all about the same size being they are all driving similar sized vehicles. also there is many different length vw axles available. also the steering rack is right on the firewall so no issue there 198...
by Bratitude
Fri Mar 15, 2024 7:36 pm
Forum: Projects
Topic: 1984 Voltswagen Rabbit Prius Gen 3 ZOMBIE
Replies: 280
Views: 16857

Re: 1984 Voltswagen Rabbit Prius Gen 3

exactly as aragorn said. your making flanges for the VW joints to bolt to.

notice the 6 bolts on the innner vw cv joint? un bolt them....now you have separated the cv joint from the flange.

now you just need a flange that has the toyota splines that go into the prius transaxle.
by Bratitude
Fri Mar 15, 2024 3:42 am
Forum: Projects
Topic: 1984 Voltswagen Rabbit Prius Gen 3 ZOMBIE
Replies: 280
Views: 16857

Re: 1984 Voltswagen Rabbit Prius Gen 3

still work in progress, hit my favorite mom n pop steel shop today (not many of these left around these parts, these days, how about in your parts of the world?) gonna slug one side and sleeve the other It’ll work great, but I just don’t think it was the right route to go :) I just think making stu...
by Bratitude
Fri Mar 15, 2024 1:16 am
Forum: Projects
Topic: 1984 Voltswagen Rabbit Prius Gen 3 ZOMBIE
Replies: 280
Views: 16857

Re: 1984 Voltswagen Rabbit Prius Gen 3

Gregski wrote: Thu Mar 14, 2024 1:19 pm and there was no shortage of Bad Ideas


IMG_2974.JPG

:?

uhg custom axles where not necessary!
by Bratitude
Thu Mar 14, 2024 8:58 pm
Forum: Nissan
Topic: IVT-Shunt Wiring Diagram Error?
Replies: 3
Views: 267

Re: IVT-Shunt Wiring Diagram Error?

i put the drawing together, yes there are to different versions of the shunt. i have a few older shunts, which i drew up the wiring for.

would be good to add these photos of the shunt pinout out to the wiki
by Bratitude
Sat Mar 09, 2024 11:48 pm
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

Some more CHAdeMO updates: FLO dc fast chargers result in an over voltage fault. I’m guessing this is a result of the isolation test? During the charger start up udc voltage rises up to 650v. Shortly after starting the charge, the zombie shut it all down. some of the newer bc hydro station seem to d...
by Bratitude
Wed Mar 06, 2024 2:58 pm
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

When I arrived at the station I immediately thought “oh can I pull an arber and charge with both at the same time?!?” Gave me a good laugh
by Bratitude
Tue Mar 05, 2024 8:59 pm
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

Just finished a 370km drive. Smooth driving. And got CHAdeMO working with zombie. First station (charge hub)charged me for time but provided 0 power. IMG_2241.jpeg The bc hydro dc fast charger(abb) worked great! IMG_2246.jpeg There’s a remote delta 25kwh fast charger at a rest stop. along with a 48a...
by Bratitude
Tue Mar 05, 2024 7:03 am
Forum: Vehicle Control (VCU)
Topic: zombiverter high speed can3 jumpers
Replies: 2
Views: 182

Re: zombiverter high speed can3 jumpers

As i thought

So the text on the back of zombie is wrong
by Bratitude
Tue Mar 05, 2024 12:20 am
Forum: Projects
Topic: ISA Shunt With ZombieVerter VCU [FINISHED]
Replies: 13
Views: 848

Re: ISA Shunt With ZombieVerter VCU [FINISHED]

Yes both powered on at the same time. I will have to get hold of an Arduino Due and CAN Shield. I have not really worked with the Arduino products before... Can i use any CP2515 CAN Bus module with the Due or does it need to be the CAN-BUS shield? in sort yes you can, i made a little board with a M...
by Bratitude
Mon Mar 04, 2024 11:56 pm
Forum: Vehicle Control (VCU)
Topic: zombiverter high speed can3 jumpers
Replies: 2
Views: 182

zombiverter high speed can3 jumpers

set up chademo in my brat with a zombieverter. some discrepancy around can 3 termination on the zombie, on the back of the zombie it says "solder jumper sj15 and sj10 for can3 termination" but in damiens chademo video he references sj10 and sj5 to solder for termination sj5.jpg damien.jpg ...
by Bratitude
Mon Mar 04, 2024 6:28 pm
Forum: Projects
Topic: ISA Shunt With ZombieVerter VCU [FINISHED]
Replies: 13
Views: 848

Re: ISA Shunt With ZombieVerter VCU [FINISHED]

I have tried both CAN1 and CAN2 with the same results. I have also run the initializing procedure multiple times and I have the 120Ohm termination resistor connected on X2 of the ISA shunt. And the shunt is powered on when you int? Do you have access to an ardunio due? https://openinverter.org/wiki...
by Bratitude
Sun Mar 03, 2024 9:46 pm
Forum: Projects
Topic: ISA Shunt With ZombieVerter VCU [FINISHED]
Replies: 13
Views: 848

Re: ISA Shunt With ZombieVerter VCU [FINISHED]

Looks like it did not initialize properly what can bus is it on? Use can1 to init
by Bratitude
Sun Mar 03, 2024 5:12 am
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

Installed a new rev 3mimi board. Using the original leaf harness with the additional pins populated. back in action. sort of. getting pre charge on boot. Regardless of firmware, Or parameter settings. so i have pull negative con high befor booting the inverter. or precharge fails and it wont cycle p...
by Bratitude
Sat Mar 02, 2024 4:24 pm
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

Scrappyjoe wrote: Sat Mar 02, 2024 4:20 pm Could I ask what an OI board is? I’ve been trying to follow along - very interesting - but I can’t get a full understanding because I can’t figure out what an OI board is.
OI = openinverter
The logic board In the leaf inverter was replaced with the open inverter board.
by Bratitude
Sat Mar 02, 2024 1:44 am
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

another stupid mistake. i loaded 5.32 SIN instead of FOC. loaded up 5.27 FOC. fired it up. click/ pop sound moment i touch the throttle. desat. lots of noise on everything. doing a full shut down and reset it will slightly spin moment i select drive, then desat. plots are with inverter on and no HV....
by Bratitude
Sat Mar 02, 2024 1:11 am
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

took a closer look at how the inverter is functioning when in drive. current firmware is 5.32 i'm getting pluses /oscillations in the motor rpm when applying a little bit of throttle (with transmission in neutral) and the same (lurching) when in gear. this happens regardless of throttle over can, or...
by Bratitude
Fri Mar 01, 2024 7:47 pm
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

Okay so nope! I blew my mid pack fuse
by Bratitude
Fri Mar 01, 2024 6:12 pm
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

okay played around the inverter can setting abit to no effect. then disconnected the dcdc can from can2 and we are back! with the transmission in neutral, i slightly pressed the throttle, and the motor spins up... too quick and it takes off. yikes. pull the for/rev switch to neutral and instant rege...
by Bratitude
Fri Mar 01, 2024 7:24 am
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

we had various errors on the bus, it was a device presumably running at the wrong baud rate makes sense, i put the inverter back on CAN1, dcdc and shunt on CAN2 and still getting timeout. ill play with the inverter can setting tomorrow new harness is now in the car, water pump and tesla charger con...
by Bratitude
Thu Feb 29, 2024 11:38 pm
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

Very good. I noticed on another build that CANCOUNTER comes up a bit too quickly. Has no practical consequence though. In Touran it isn't thrown, weird strange. i put the shunt and inverter on can1 as i had the shunt on can2 and inverter on can1, now the inverter shows CANTIMEOUT so there must be s...
by Bratitude
Thu Feb 29, 2024 9:03 pm
Forum: Projects
Topic: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)
Replies: 166
Views: 48345

Re: [DRIVING] leaf powered 1983 Subaru BRAT (dual outlander WIP)

we have a driver! mapped the throttle (pot min/max) on the inverter. selected drive via zombie, pressed throttle via zombie, motor spin! wiring is kind of funky then, should i wire the inverter start input to the zombie "inverter power" output? as zombie will take care of the start up sequ...