Search found 1585 matches
- Wed Mar 27, 2024 7:34 am
- Forum: Toyota/Lexus
- Topic: Gen 3 Prius Transaxle P410 Makes Clunky Noise.
- Replies: 25
- Views: 358
Re: Gen 3 Prius Transaxle P410 Makes Clunky Noise.
Might as well weld up the PSD now it's there
- Sun Mar 24, 2024 1:56 pm
- Forum: Projects
- Topic: [DRIVING] VW Beetle 2003
- Replies: 325
- Views: 89065
Re: [DRIVING] VW Beetle 2003
I had a pair of contactors, Tesla ones, one welded one didn't. The unwelded one appeared to measure fine when closed but under load it was higher resistance. So replaced both now. So on to the cool photos of the inverter igbts IMG_20240324_104701453.jpg IMG_20240323_185512418.jpg Cars back to runnin...
- Thu Mar 21, 2024 3:53 pm
- Forum: Toyota/Lexus
- Topic: Gen 3 prius inverter only 245 amps
- Replies: 4
- Views: 436
Re: Gen 3 prius inverter only 245 amps
170A from the battery as reported by my ISA shunt
- Thu Mar 21, 2024 2:54 pm
- Forum: Projects
- Topic: 1984 Voltswagen Rabbit Prius Gen 3 ZOMBIE
- Replies: 281
- Views: 16971
Re: 1984 Voltswagen Rabbit Prius Gen 3
Did you really start this last year in secret and now releasing all the footage?
- Thu Mar 21, 2024 9:32 am
- Forum: Toyota/Lexus
- Topic: Gen 3 prius inverter only 245 amps
- Replies: 4
- Views: 436
Re: Gen 3 prius inverter only 245 amps
I have throtcur at 4.5, my params are here https://openinverter.org/parameters/view.html?id=30 and once moving I've had phase currents of 450 amps with logs I've taken previously. I do have MG1 and MG2 paralleled though
- Wed Mar 20, 2024 2:23 pm
- Forum: Projects
- Topic: 1984 Voltswagen Rabbit Prius Gen 3 ZOMBIE
- Replies: 281
- Views: 16971
Re: 1984 Voltswagen Rabbit Prius Gen 3
Man you're making my project seem glacial paced.
- Wed Mar 13, 2024 4:38 pm
- Forum: Projects
- Topic: [DRIVING] VW Beetle 2003
- Replies: 325
- Views: 89065
Re: [DRIVING] VW Beetle 2003
The gs450h is using OEM control signals. I'm making the Prius inverter do things Toyota would never do with the logic board replacement
- Wed Mar 13, 2024 10:45 am
- Forum: Projects
- Topic: RARE 1984 Volkswagen Rabbit - Electric - $500 (Davis)
- Replies: 14
- Views: 643
Re: RARE 1984 Volkswagen Rabbit - Electric - $500 (Davis)
Added a poll for you Obviously it's result is legally binding.
If that was close to me, it would be on my drive already.
If that was close to me, it would be on my drive already.
- Wed Mar 13, 2024 10:33 am
- Forum: Projects
- Topic: [DRIVING] VW Beetle 2003
- Replies: 325
- Views: 89065
Re: [DRIVING] VW Beetle 2003
It usually does, the car has always struggled to get up her drive in reverse, sometimes I could make it up with a bit of a run up, othertimes the hardware protection cut out.
- Tue Mar 12, 2024 11:37 am
- Forum: Projects
- Topic: [DRIVING] VW Beetle 2003
- Replies: 325
- Views: 89065
Re: [DRIVING] VW Beetle 2003
I've no idea. Full throttle on the road is fine but on the drive, it didn't have the umph and so was a stalled motor at full throttle maybe the 4.5 throtcur (450a) isn't possible on the motor while it's spinning with the back EMF?
- Tue Mar 12, 2024 9:54 am
- Forum: Projects
- Topic: [DRIVING] VW Beetle 2003
- Replies: 325
- Views: 89065
Re: [DRIVING] VW Beetle 2003
Cars been running great all year, had a weekend away, multiple DCFC and destination charging, faultless. IMG_20240309_101912930.jpg IMG_20240310_121227497_HDR.jpg IMG_20240309_122155421_HDR.jpg Went to my mothers and tried to get up her very steep driveway. Boom, Prius inverter RIP. Had to do a road...
- Thu Mar 07, 2024 12:42 pm
- Forum: Projects
- Topic: [ WIP ]Bmw e39 + GS450h
- Replies: 19
- Views: 2422
Re: [ WIP ]Bmw e39 + GS450h
The STLs for those parts available? I like the needing of bolts to get to the HV
- Sun Mar 03, 2024 8:41 am
- Forum: Toyota/Lexus
- Topic: Gen 3 dual board small udc not reading
- Replies: 16
- Views: 488
Re: Gen 3 dual board small udc not reading
Most likely culprit is the 50 pin connector, I'd check it a fourth time, the specific pin. It was a dry joint on my single board with UDC not working
- Wed Feb 28, 2024 2:23 pm
- Forum: Projects
- Topic: [WIP] BMW Z3
- Replies: 282
- Views: 143945
Re: [WIP] BMW Z3
I'm not sure that I do
- Wed Feb 28, 2024 2:10 pm
- Forum: Projects
- Topic: [WIP] BMW Z3
- Replies: 282
- Views: 143945
Re: [WIP] BMW Z3
Give it a send off with a bang?andybpowell wrote: ↑Wed Feb 28, 2024 2:03 pm In all seriousness I really need to change the diff before it disintegrates, it sounds bad
- Wed Feb 28, 2024 2:00 pm
- Forum: Projects
- Topic: [WIP] BMW Z3
- Replies: 282
- Views: 143945
Re: [WIP] BMW Z3
sounds perfect, that was only 30% throttle too?
- Wed Feb 28, 2024 1:56 pm
- Forum: Projects
- Topic: [WIP] BMW Z3
- Replies: 282
- Views: 143945
Re: [WIP] BMW Z3
We. Need. Video.
- Wed Feb 28, 2024 1:17 pm
- Forum: Projects
- Topic: [WIP] BMW Z3
- Replies: 282
- Views: 143945
Re: [WIP] BMW Z3
I've sent you a bin with a change from Tom, possibly fixing this limit issue. God Speed
- Tue Feb 27, 2024 12:53 pm
- Forum: Projects
- Topic: [WIP] BMW Z3
- Replies: 282
- Views: 143945
Re: [WIP] BMW Z3
FrontRearBalance doesn't seem to do anything. It's hardcoded to 50 for all vehicles except Subaru but doesn't seem to be used for anything.
- Fri Feb 23, 2024 4:51 pm
- Forum: Inverters / Motor Controllers
- Topic: HELP Please - need (paid) assistance Rev2 Inverter UK
- Replies: 4
- Views: 354
- Fri Feb 23, 2024 12:32 pm
- Forum: User Interface
- Topic: interface problem tesla sdu with esp32 canlite module
- Replies: 27
- Views: 889
Re: interface problem tesla sdu with esp32 canlite module
I've downloaded the images and attached to post.
- Mon Feb 19, 2024 12:12 pm
- Forum: Projects
- Topic: [WIP] BMW Z3
- Replies: 282
- Views: 143945
Re: [WIP] BMW Z3
BIN PM'd
- Mon Feb 19, 2024 11:24 am
- Forum: Projects
- Topic: [WIP] BMW Z3
- Replies: 282
- Views: 143945
- Mon Feb 19, 2024 11:16 am
- Forum: Projects
- Topic: [WIP] BMW Z3
- Replies: 282
- Views: 143945
Re: [WIP] BMW Z3
int8_t is unsigned integer. Did it fix the cutting out though?
- Mon Feb 19, 2024 10:27 am
- Forum: Projects
- Topic: [WIP] BMW Z3
- Replies: 282
- Views: 143945
Re: [WIP] BMW Z3
https://github.com/damienmaguire/Stm32-vcu/pull/76 Has the fix, apply that and you're golden.
Also https://github.com/crasbe/ZombieBuild is the easiest way to build
What about when it's below 0?
Also https://github.com/crasbe/ZombieBuild is the easiest way to build
Code: Select all
temp_inv_water=int8_t(mth_data[20]);