Search found 57 matches

by Jackk
Wed Apr 19, 2023 8:34 pm
Forum: Toyota/Lexus
Topic: Run GS450H Oil pump linear to rpm
Replies: 2
Views: 376

Run GS450H Oil pump linear to rpm

Is it atall possible to cycle the oil pump pwm output to increase linear with rpm? Has anybody achieved this? It seems pointless to have the oil pump running whilst stuck in traffic. Mine is fairly noisy. Currently set to 30%. (Running zombieverter) Any ideas would be great... I guess the vcu has al...
by Jackk
Sun Mar 05, 2023 5:40 pm
Forum: Toyota/Lexus
Topic: Max Rpm Gs450h
Replies: 22
Views: 2104

Re: Max Rpm Gs450h

Ok understood, Does anyone know if the rev limit within Zombie verter web interface records MG1 or MG2? If its MG2 then MG1 would be spinning faster no? I'm worried if I set max speed to say 12500 then MG1 may exceed its max rating? With my diff ration setup @ 3.545:1 I'm trying to get the max rpm I...
by Jackk
Tue Feb 28, 2023 10:30 pm
Forum: Toyota/Lexus
Topic: Max Rpm Gs450h
Replies: 22
Views: 2104

Re: Max Rpm Gs450h

PatrcioEV-ATX wrote: Tue Feb 28, 2023 8:15 pm I have mine set to 11k but I haven't hit that yet. The original user friendly software had it set at 10k. Most of the discussion in the support thread says 10-11k.
Thanks!
by Jackk
Tue Feb 28, 2023 2:59 pm
Forum: Toyota/Lexus
Topic: Max Rpm Gs450h
Replies: 22
Views: 2104

Max Rpm Gs450h

I found a few people suggesting different max rpm limits for the GS450H. Does anyone know the exact limit before I accidently explode mine. My current limit is set to 7500rpm and the car tops out at 70mph. Ideally I want quite a bit more revs but don't want to risk upping it until id ask... The car ...
by Jackk
Fri Feb 17, 2023 1:14 pm
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

UPDATE. Thanks to everyone for the help. I took the car out for another test just now while playing around with some parameters. My ISA seems to be reporting sensible values. I saw 350 amps max. I then played around with UDCmin. This was set to the correct value of 512v. I put this down to 400v and ...
by Jackk
Wed Feb 15, 2023 5:00 pm
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

How is your throttle pedal calibrated are you leaving enough room for noise? If this happens when pedal is fully pressed could it be that the pedal is in the territory where it gets outside of the calibrated area due to noise/wrong calibration? Ill re calibrate it but fyi its nowere near flat out w...
by Jackk
Wed Feb 15, 2023 4:13 pm
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

Update.... So I replaced the encoder wires with 6 core shielded wire. Funnily enough the original cables I had installed were twisted and had copper tape wrapped around the whole length but was not grounded at the inverter end. With the new shielded cable installed it still has the terrible cut out....
by Jackk
Wed Feb 15, 2023 10:08 am
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

evMacGyver wrote: Wed Feb 15, 2023 9:17 am So your resolver cables are not shielded and shield grounded as wiki connections tells to do:
https://openinverter.org/wiki/images/b/ ... ctions.png
You really really really should do it.
Indeed Ill try and get this done today and report back!!
by Jackk
Tue Feb 14, 2023 2:34 pm
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

Hello, Firstly thankyou so much for looking into this! Please see attached parameter file... Here is the first torque graph. I booted it only once and you can see the torque cut clearly in the graph... It seems while the pedal is depressed after the cut it applies no torque. You have release throttl...
by Jackk
Fri Feb 10, 2023 10:47 am
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

Unfortunately splitting pack down would be something I really want to avoid as it would be a major setback/ very difficult. There is a chap from USA called mauswerkz he ran a gs450h successfully at 650v. Does anybody know anyone else who has successfully run 600V? One thing I will say removing the c...
by Jackk
Thu Feb 09, 2023 9:28 pm
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

Unfortunately yes it shows 1.11.

One thing to note which may be unique about my setup from most people is that I'm running 600v nominal.

Would this increase the likelihood of noise?
by Jackk
Thu Feb 09, 2023 4:03 pm
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

UPDATE. I took the time to replace the four twisted serial cables to screened cable. The shields are all soldered to one wire near the inverter plug then this lead approx 20cm long connects straight to the inverter casing. The inverter itself has a seperate ground strap which goes to chassis. The 4x...
by Jackk
Tue Feb 07, 2023 9:21 pm
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

I have set my car as per Damiens video with the 1.11 update and it has fixed my torque drop. My RPM was set at 6000 and the rev limit was noticable but not violent. Other settings when I drove the car were, as far as I can recall, throtmax 50% and throtramp set at 1. I have not tried the car with a...
by Jackk
Tue Feb 07, 2023 4:12 pm
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

Hello all, I have a gs450h zombie-verter and am experiencing the same violent cut in power. I have just flashed zombie to V1.11A and sadly the fault is still there. Just thought id share that I am experiencing the same troubles. I will try to resolve. If I get anywhere ill be sure to post on here. ...
by Jackk
Tue Feb 07, 2023 2:42 pm
Forum: Toyota/Lexus
Topic: GS450h Cuts Out on Heavy Throttle Application SOLVED
Replies: 60
Views: 5760

Re: GS450h Cuts Out on Heavy Throttle Application SOLVED

Hello all, I have a gs450h zombie-verter and am experiencing the same violent cut in power. I have just flashed zombie to V1.11A and sadly the fault is still there. Just thought id share that I am experiencing the same troubles. I will try to resolve. If I get anywhere ill be sure to post on here. J...
by Jackk
Fri Sep 09, 2022 7:17 pm
Forum: Charging
Topic: BMW i3 CCS/charge port controller
Replies: 1187
Views: 3365329

Re: BMW i3 CCS/charge port controller

Thanks but I was actually referring to the inverter pre charge?

I am right in thinking the lim controls the main contactors?

Still would like to know why this is actually necessary? Is it just an extra safety measure?

J
by Jackk
Fri Sep 09, 2022 2:43 pm
Forum: Charging
Topic: BMW i3 CCS/charge port controller
Replies: 1187
Views: 3365329

Re: BMW i3 CCS/charge port controller

Hi all,

Does the lim control pre charge ? From what I can see from the pinout there are only outputs for the main and CCS contactors.

What is the best way to handle pre charge?

Before lim module was fitted my gs450h V2 board dealt with it and obviously main contactors.
by Jackk
Mon Aug 01, 2022 9:42 pm
Forum: Charging
Topic: BMW i3 CCS/charge port controller
Replies: 1187
Views: 3365329

Re: BMW i3 CCS/charge port controller

Is there a voltage sense board suitable for higher voltage? as on the wiki it suggest max 500v...... Yes, our Voltage sense board for BMW i3 LIM CCS fast charging can do up to 750V. Even more in terms of isolation, but then some clipping occurs. See attached photo where it measures 1044V and produc...
by Jackk
Mon Aug 01, 2022 9:36 pm
Forum: Charging
Topic: BMW i3 CCS/charge port controller
Replies: 1187
Views: 3365329

Re: BMW i3 CCS/charge port controller

EV_Builder wrote: Mon Aug 01, 2022 11:48 am I'm not sure if even the chargers can reach 650Volts.
Maybe a good check would be how the TayCan charges it's pack I bet it has a internal DC/DC step up converter.
Perhaps although I did see this printed on the side of a CCS charger the other day .... Suggest 900v max
by Jackk
Mon Aug 01, 2022 11:34 am
Forum: Charging
Topic: BMW i3 CCS/charge port controller
Replies: 1187
Views: 3365329

Re: BMW i3 CCS/charge port controller

Wanted to ask about CCS voltage range. I am running a 600v nom pack. Charging voltage would be 650v ish. On the WIKI it says the later LIM modules voltage range is 0-1000v which is promising. My question is... Is there a voltage sense board suitable for higher voltage? as on the wiki it suggest max ...
by Jackk
Fri Feb 11, 2022 9:35 am
Forum: Tesla
Topic: Tesla Large Drive Unit Support Thread
Replies: 802
Views: 127131

Re: Tesla Large Drive Unit Support Thread

There’s a light on each Tesla phase gate driver board that will illuminate during a desat fault. That’ll tell you for sure it’s a hardware issue. I don’t have a photo immediately handy. EDIT. Found my old pic from Instagram. Haha out of interest does this light illuminate the time ? Or does HV need...
by Jackk
Tue Jan 11, 2022 11:43 am
Forum: Battery Managment (BMS)
Topic: Orion cell tap validation tool
Replies: 3
Views: 1198

Re: Orion cell tap validation tool

Jackk wrote: Tue Jan 11, 2022 11:42 am Hi does anyone have a orion bms 2 cell tap validation tool I can rent or buy?

Zero are out of stock and could do with one asap...

Thanks...

Jack
I am based in the U.K
by Jackk
Tue Jan 11, 2022 11:42 am
Forum: Battery Managment (BMS)
Topic: Orion cell tap validation tool
Replies: 3
Views: 1198

Orion cell tap validation tool

Hi does anyone have a orion bms 2 cell tap validation tool I can rent or buy?

Zero are out of stock and could do with one asap...

Thanks...

Jack
by Jackk
Tue Dec 07, 2021 9:38 pm
Forum: Toyota/Lexus
Topic: GS450H Discussion
Replies: 377
Views: 75271

Re: GS450H Discussion

Quick question...

What are people using to cool atf ?

How large oil cooler is really needed?
by Jackk
Tue Sep 21, 2021 2:43 pm
Forum: Toyota/Lexus
Topic: Lexus GS450H VCU Support Thread
Replies: 775
Views: 430013

Re: Lexus GS450H VCU Support Thread

ok thanks look like ill have to jump on the zombie band wagon and order one up!!

J